Hi all
I need a little advice and some ideas for service and contracts on copiers and printers.
What are companies doing with customs that decide to buy their equipment...
Type: Posts; User: Geo
Hi all
I need a little advice and some ideas for service and contracts on copiers and printers.
What are companies doing with customs that decide to buy their equipment...
Is it possible the firmware has a bug in it given the error code only happens with thick type stock and always before the transfer roller
I wish..this unit has 5 trays and it will give code 611.xx from all trays.. AND playing with it , it doesn't code out if the trays are set plane paper etc, but will for thick , heavy stock types
Hi All
Help
Getting a constant paper stoppage just before the transfer roller and a "printhead error 611.37 " also 611.35 .
No paper jam message .
Checked all sensors , paper feeds etc....
Thanks for your answer and links..BUT , you didn't answer the question..Try again?
Hi folks..
Just a simple question to all that believe in human made "climate change/global warming " , What percentage of "climate change" is directly caused by human activity....
Maybe you've seen this before on the color Irises:
Goes into ready state and when making copies , may of may not go to add toner after 5-6 copies for 10-15 SEC. If add toner when making copies ,...
Thanks
Problem is , I did try a new DV unit and a couple of used good ones.. Making copies of blank org or ones with print doesn't make a deference as to how many output before...
Hi
Thanks , I do know what the code is ..Problem is , haven't been able to fix it..
Hi
Need a little help from the brain trust..
CS 5003Ci with 1.1 million.. Unit will go into warm up and into ready state and will allow 1-2 copies , more than 5-6 and will code...
Another thought... Other than the laser assy , did you check the transfer roller press springs and the side door latches.
I always replace the unit, but I'm curious as to the why..Not sure I can agree with your diagnosis for all cases . . I have had the code pop up at 60 K and the bearings "seemed" OK..I know the...
Yes...It seems as if there is a timing issue or perhaps a thermistor gets a little weak ,
Hi Folks
Has anybody bothered to figure out why these fuser will give a C6600 or C6670 error after being shut down overnight.. The codes will clear with a power cycle and will work...
A couple of thoughts...Were ALL the shipping spaces removed from the transfer belt..Does a DV refresh have any effect ? IS OEM toner being used..?
Trying to look up the tech bulletin ..but for some strange reason ..Astia isn't still doesn't like me..
I will check the sensor , but I doubt it , only 15k after replacing the drive assembly and the copier seems to be running clean..I think..But I will definitely
check it..
Thanks
Replaced the stupid thing 5-6 months ago...could it have gone bad?
Thanks
Hi all
Looking for help yet again..
CS3252ci with an intermittent C2700 code...
Code first happened 6 months ago Replaced TRANS belt no joy , replaced trans drive...
Hi
Sorry for not responding sooner..
You folks were spot on ..it was the width size arm , wasn't making good contact with switch.
I couldn't check the bulletin, the 3 week update...
Hi
Not reading the correct size in the tray..for example will read folio when it's letter..
I know this will be something stupid that I am overlooking...It's a simple set up..
Very familiar...
Hi All
Long time no see.....
Has anybody run into problems with some of the 2 series not properly reading the paper size in the cassettes. ?
I know this should be a simple fix , but I have...
Hi
Trying to get a hold of you...Please call me or E-Mail..
Thanks..
Sorry for the delay in responding , I'm not always getting updates..
Whats a good time to call you...
Thanks
Sounds good ..what is your phone number , I would like to talk to you...
Thanks