Search:

Type: Posts; User: rdyjnkns

Page 1 of 6 1 2 3 4

Search: Search took 0.02 seconds.

  1. [Jamming] Re: Sharp MX101N - 2nd transfer belt not turning.

    Greetings fellow technicians. I apologize for the delay as I'm in the process closing down the shop's operations. Anyway. I found both the clutches on EBay. They have been replaced and the copier is...
  2. [Jamming] Re: Sharp MX101N - 2nd transfer belt not turning.

    Greeting. I am in need of a primary transfer assembly clutch, part number PCLC-0378FCZZ, for this Sharp MX-4101 copier. I found one on Ebay yesterday, but was informed by the vendor...
  3. [Jamming] Re: Sharp MX4101N - 2nd transfer belt not turning.

    Thanks Zootech. Hopefully I won't have to do this again.
  4. [Jamming] Re: Sharp MX4101N - 2nd transfer belt not turning.

    Greeting fellow technicians. I have received the new primary transfer belt assembly clutch and I believe the best way to perform the repair is to remove the whole drive section. I have attached a...
  5. [Jamming] Re: Sharp MX101N - 2nd transfer belt not turning.

    I will, MoochPage. But something tells me it is going to be a bear to remove the old one. And there are no instructions in the service manual. But I got to this point. Just have to take photos.
  6. [Jamming] Re: Sharp MX101N - 2nd transfer belt not turning.

    Thanks OlliK1969. The code changed to L4-06 which is the Primary Transfer Belt Assembly clutch (see attached photo). 53583
  7. [Jamming] Re: Sharp MX101N - 2nd transfer belt not turning.

    Greetings. Good news - the problem has been resolved. The gear that drives the primary transfer belt was missing its screw. Bad news - now I have the LA-04 code which has to do with the primary belt...
  8. [Jamming] Re: Sharp MX101N - 2nd transfer belt not turning.

    I want to thank all of you for your assistance. I will be seeing the customer in the morning (they open at 6:00 PM PST). At least, I will be the traffic on the US15 North. I will keep you informed.
  9. [Jamming] Re: Sharp MX101N - 2nd transfer belt not turning.

    Thank you. I will take a look at that.
  10. [Jamming] Re: Sharp MX101N - 2nd transfer belt not turning.

    Sorry, MX-4101N. Wish I could delete and start again.
  11. [Jamming] Sharp MX101N - 2nd transfer belt not turning.

    The 2nd transfer belt is not turning which is causing an accordion jam. I marked both the belt and the drive gear and neither the belt or the gear is turning. I believe it could be the motor, but I...
  12. [Jamming] Sharp MX101N - 2nd transfer belt not turning.

    The 2nd transfer belt is not turning which is causing an accordion jam. I marked both the belt and the drive gear and neither the belt or the gear is turning. I believe it could be the motor, but I...
  13. [Misc] Re: Part number found; not in manual -- M402/M426

    Greetings tech0419,

    I ran into the same problem. The cassette for tray 2 would not seat properly due to the fact that the sensor was stuck forward of the stop. The end user not knowing this may...
  14. [Misc] Re: Sharp MX-3070N , TLS support and access simulation mode

    In regards to the encryption, thank you. As for the question about the version, I did the procedure as per the service manual (double-click the HOME button). The Ver didn't appear on the screen...
  15. [Misc] Re: Sharp MX-3070N , TLS support and access simulation mode

    Thank you for your assistance.
  16. [Misc] Re: Sharp MX-3070N , TLS support and access simulation mode

    Thank you. I will make note of that.
  17. [Misc] Sharp MX-3070N , TLS support and access simulation mode

    Greetings. My customer is upgrading from the Sharp MX-4101 to the Sharp MX-3070N. I did a recon to the device and according to the spec sheet under "Network and Data Security", one of the features...
  18. Replies
    9
    Views
    1,457

    Re: Sharp MX 4101N Will not boot up

    My customer is going to upgrade to a newer model of Sharp. Thanks for the assistance.
  19. Replies
    9
    Views
    1,457

    Re: Sharp MX 4101N Will not boot up

    Greetings. I resolved this problem. The MFP Controller was a pull from another Sharp MX 4101NX copier. More then likely, it had come off it's lease and had a high meter. Anyway, it blew 3 of the 6...
  20. Replies
    2
    Views
    2,430

    Sharp MX-4101nx cannot locate smtp server

    Greetings. My customer's Sharp MX-4101NX would not scan to email even though it can still print from their workstation as well as copy and fax. The network admin changed the email server from...
  21. Replies
    9
    Views
    1,457

    Re: Sharp MX 4101N Will not boot up

    Good afternoon my fellow technicians. So, I installed the new MFP CONTROLLER after transferring all the EPROM, DIMMS, and HDD to the new PCB. The copier booted up and the customer can print, fax and...
  22. Replies
    9
    Views
    1,457

    Re: Sharp MX 4101N Will not boot up

    In regards to swapping the HDD between the 2 boards, no. I could try this tomorrow when I return in the morning. I'm trying to get a RMA for the MFP Controller we received yesterday. As I said, when...
  23. Replies
    9
    Views
    1,457

    Sharp MX 4101N Will not boot up

    The customer's Sharp MX 4101NX will neither scan to email (Selected servers are not found). I can ping the server from the copier from the onboard network settings. Also the end users can print from...
  24. Re: FS4200 Eject/Feed Shaft section will not feed paper

    There is no jam code displayed. And I have not been able to access the error log as per the serviced manual (see attached).
  25. FS4200 Eject/Feed Shaft section will not feed paper

    After I replaced the fuser assembly in my FS4200 (due to a PCQ issue), the EJECT/FEED SHAFT ASSEMBLY will not accept the print job from the fuser. In other words, no gear movement. I installed the...
Results 1 to 25 of 135
Page 1 of 6 1 2 3 4