Search:

Sorry, you are right.

I found the partnumber in the parts catalog page 120 (acessory parts)

A5AWR73500 Deflection Sensor Assy

43992

Hi Allan,
in my opinion, there is no PS40 in the PF-707.
The PF-707 is the Paper Feed Unit from C1100, C2070 and newer Series.
Both Series have a Sensor inside the print system.

Christian

Hello Cidermonkey,

you need the Option OR-102.
While installation you have to activate DipSW 15-0

If you work with a 1060​L I think you need a special patch for the IC-415 to connect it to the Printsystem.

Hello texchar555, here in good old germany we have a "Oktoberfest" and we have a PM-Kit for C8000 :).
The partsnumber for this kit is A1RF-SMP.

Christian

Hello Francois d,

in the adjustment mode there is a mode to polish the fusing roller.

Adjustment -- 02 Execute Adjust operation -- Fusing Refresh Mode
For more information about this refresh...

Hello cmateus,

the error code C-2801 says, that the gamma correction in yellow is aborted.
The units in failure can be:
Printer Control Board PRCB
Developing unit /y
Gamma Sensor PS11
...

Hi Condor99,

have you this problem with all kinds of paper?
In my mind, there was a setting for a black problem with thick paper. Think it was a DipSW.

Christian

Hello Teqorious,

I think you have the uneven density caused by wrong mounted grid of the charging corona.
Print testcharts with 50% density cyan (magenta) and measure the denstity of the...

Hello Toxic,
to install a system to a USB flash drive you need the USB Flash installer CD.
With this CD you can boot your PC it starts a Knopix system. Than you have to connect the USB Flash drive...

Hello sanimir,

this two parts number are for the same DU-101.
I think 020EE was the "old" number for Konica 8050, 020EH is for C500.

The DU-101 with parts number 020EH is for all systems 8050...

Do you have toner from C500?

Hello sanimir,

you can set DipSW 1-2 and 1-3 to "1", than the system runs till it is defect. But with this setting you will kill the developers 100%.

Good luck
Christian

Hello internetfab,

in the attachment is the description from the service manual.
I think the up/down drive from the finisher tray is broken.

regards
Christian

Hello seniortech,

I think, there is no possibility to disable this message.

regards
Christian

Hello sanimr,
the toner from C500 and 8050 are not the same.
In the C500 the toner is modified.

regards
Christian

Hello Nic,

you can only print on a custom paper size.
For SRA3 you must use 320x450mm.
You can set this in the C500 as user defined paper size, and you can set it in the PS Driver.

Regards...

Hello Stirton.M,

good luck for you and your sales team.
I have solves the training for the C8000 too and we have at this time three systems in our field and one system in our showroom.
Our...

Hello together,
I would like to open a new thread to collect any information about C8000.
Who has practical knowledge about this system?
Whats your experience?

Best regards
Christian

Hello retro,

I think it is possible, that the Image Processing Board or the Printer Control Board is defekt.
The IPB get the signal from the centering sensor and starts to write the image in Main...

Hello retro,
no, that affect is only at LU-202.
Is the image shift on the first or on the second side? In the ADU, is another centering sensor, but it is only for the second side.
I have no other...

Hello retro,
there is a centering sensor in the LU. If the paper comes in a wrong postition to this sensor, he shit the image to the "right" position.
It is possible, that the sensor is defekt.
We...

Hello internetfab,
the errorcorde says that there is a communication error from ADU Conveyance drive board.
It is possible, that the PRCB or ADU CVDB is defekt.
Check all cables and connectors...

Hello seniortech,

you can try to cut the cable a little bit, but I think it is better to change the cable

regards
Christian

Hello internetfab,

the code J-9301 is a paperjam from the PS20 in the duplexunit.
We have often problems with this sensor, it is also possible that the problems comes from the decurlingroller....