I replaced the magenta dev unit and drum and the problem went away. I did change drums first ... the problem stayed on the magenta, it was the new developer unit I installed, must have been a bad...
Type: Posts; User: MrBafner
I replaced the magenta dev unit and drum and the problem went away. I did change drums first ... the problem stayed on the magenta, it was the new developer unit I installed, must have been a bad...
I managed to fix the scratch issue on the image .. it was a bit of toner on the black shelf / panel under the black / cyan drums/developer unit.
However now, I am getting 093-315 .. I have...
Thank you ... good advice, will get some IPA and try it out. Just cleaning the wiper didn't help at all.
Last week I had an issue with black, ended up lifting the top of the machine and cleaning the ROS, the black is now printing fine.
Now I have a problem with the magenta image streaking .. changed...
Thankyou so much for the reply. Have cleaned the laser .. you think I should replace the laser?
Have put in a brand new developer units, I was certain that was the problem.
Only other thing...
Most gear grinding noises come from drums or developer assembly's .. occasional tray 5 and the odd occasion is the 2nd btr
Hi there,
Can someone please send me a service manual for the Xerox 700i ?
Much appreciated and thank you
Did it fix the problem when you changed the 2nd BTR ?
I'm having a very similar issue, but my image is fading in the center and darker on both sides. Have done the exact procedure you have done...
No, I don't have PWS :(
Have cleaned the 1st btr roller and the 2nd btr unit .. didn't make any improvements at all.
Only thing that I can think of was to clean the laser and even though it was so hard to get to, it too...
I am not familiar with Altalink C8055, but on the commercial machines that I have worked on I found that sometimes the ITB cleaning assembly needs to be reset or replaced. You can clean them manually...
I am going to try another developer (ROS) unit ... I only have 1 bag of black developer left.
Have this imaging problem with black ... have replaced the toner, drum, dev unit, ibt belt and still having imaging issues.
The edges print heaps darker and the center terrible.
50951
When...
Does anyone know of any reliable sites that still has old Xerox printer drivers. I have spent hours looking and have tried several other drivers to no avail.
DocuColor 5065
DocuCentre 6500-III...
If I print out the swatch colour sheet I get the colour that I'm trying to print.
If I select that swatch colour box and place it as a background colour box it prints as though it is faded and...
Am after the part number for a tray 1 and tray 2 paper tray for a xerox 700i please.
Tray 1 has a snapped off arm and tray 2 just errors to 072-210 and won't function.
Looks like you need a new drum or dev unit.
NVM 762-313 cleared the error, reset it to 0
This is the NVM of the Xerox 250
I have changed the following :-
* A new drum
* A new dev unit
* A new magenta toner motor
Still have the error displayed 093-315
The error is 093-315 and I can only find the NVM for the J75, not the 700.
Can anyone give me the NVM for the 700 please ?
I have NVM 762-317, but it doesn't clear the error.
I replaced the entire toner distribution tray with one that was in a Xerox 5580. I had to remove all the caps from the toner cartridges to get them in.
Topped up the developer powder in the dev...
Do you just clean the roller or the entire 2nd BTR unit ?
There is a tray in the 2nd BTR that has a build up of toner. You need to get in with a vacuum and clean it all out.
OMG .. went through the sequence again, of course I never replaced the dispense motor, nor the board this time.
I cleaned the developer unit and reloaded.
Made sure the NVM 762-315 to 0...
Yes .. after doing it 3 times it is noticeable that toner is being dispensed.
Yes, both made the same hmmmm with a motion noise. Both toners are full.