Alrighty.. appreciate ya stoppin by. If I have questions in the future, I'll try and find this thread and ask it here and hopefully you'll get notified. Might just need your help again. May not be...
Type: Posts; User: TEKK09
Alrighty.. appreciate ya stoppin by. If I have questions in the future, I'll try and find this thread and ask it here and hopefully you'll get notified. Might just need your help again. May not be...
I have turned off reminders but could not find this particular one.
Do those parts have chips on them, or a way of resetting the counter?
I guess the obvious answer is yes.
Might be the first...
THAT WAS IT!
I took a close look at the part that's attached to the inner end piece with 2 screws. I saw where the screws had been from the pattern they made, put them back there, and FIXED.
I'll...
I think you nailed it! Won't know until I get back out there. I DID loosen that piece not paying enough attention, where I hadn't in the past when I cleaned the unit. Did not realize it was...
Well I have taken them apart to clean before several times and copies were really good afterwards. Not this time tho. I don't recall seeing any adjustment for the charger. And I don't really think...
Had to fix a gray streak on the front side, so I disassembled and cleaned the black drum unit. Put it back together and cleared up the streak, but now it's light on front side where it hadn't been...
2 new Maintenance Cartridges put in but the message won't go away. No ink had been ejected into them. The printhead was also replaced because the machine said to. Afterwards, got test prints that...
I was hoping to find someone who had done it already. Pretty sure someone out there has. If someone has and knows, please shoot us a quick note here.
Otherwise, I think I will go ahead and get...
Well I'd order a Kyocera blade if I knew it would fit. Sold here:
Results for 2BL18300
I cleaned this one and it did help. Did not fix it tho.
Does anyone know if the drum blade that fits all of these models, will also fit a TaskAlfa 5550ci?
Kyocera KM-2530
Kyocera KM-3035
Kyocera KM-3050
Kyocera KM-3530...
Great tip! So I can take a new Black Muratec Drum and simply swap the blue piece from a color drum and then that new black drum will work as a new color drum? And that'll take care of the 'chip...
I want to use Konica brand supplies in a Muratec MFX-C2880. A compatible cartridge is made to fit in either, but I'm pretty sure a Konica TN-321 will not fit in a Muratec. Does anyone know a way to...
I want to use Konica brand supplies in a Muratec MFX-C2880. A compatible cartridge is made to fit in either, but I'm pretty sure a Konica TN-321 will not fit in the Muratec. Does anyone know a way...
Thanks a lot for the support. In the case of katun toner, i hold out the possibility that the unit may have gone bad even with oem, but how can that be proven? don't think it can. Please let me...
An old-fashioned stargazer gets outside to do it. You can see things that won't show up on your computer! I'm talking about this stuff here: BLACK SKY WATCH’s Videos on Vimeo
You might be blown...
Pretty sure the problem is the black developer unit. It looks okay, but when you try and turn it by hand, it's almost impossible. What are the chances of non-oem supplies causing that? The other...
It is actually a Muratec MFX-C2880. I think it's a Bizhub C284?
Problem occurs on copies and prints. Could happen on the first page, or anywhere in the middle of a 20-page run for example, on...
Does anyone have one of these on their back shelves? I need a new one. Thanks.
Attached shows magenta and cyan registration off, to the side, instead of vertical.
The door linkage that locks the cartridges in place as it's closed were bent/broken.
I found a way to keep the...
THAT WORKED! Had a little trouble with it because I expected 'Maint Mode' to show up after I did the 3-key combination. Found out it was added as a selection below the 3 that I mentioned above. ...
I tried to do that. When I pressed 'system menu' I found out that 'service mode' does not show up. The closest it gets is 'service setting', and then you get 'print svc status page' or 'print...
I tried getting into Service Mode, but could not. I wonder if you have any other suggestions about that.
I tried opening the cover above the toner and entering 10871087 but it did not respond. ...
I thought the purpose of zero-cross is to switch the power on/off at any zero point in the AC sinewave. That way, there are no spikes injected onto the AC power line, because when the switching...
Don't have a manual for this model.
The code is Fuser right?
Try resetting via U163?
Get into Svc Mode with 10871087 right?
Another model says 6400 code has to do with Pwr Supply....