Search:

Type: Posts; User: femaster

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    247
    Views
    49,945

    Re: Konica c224 e can't access service mode

    These should get you in:






    MFP Serial Number
    A5C4021186145
  2. Replies
    4
    Views
    159

    [Misc] Re: Konica C224e MFP Reset Tool

    I've updated my original post to bit a bit clearer, but the gist of it is:
    Go into service mode as you normally would. When the password screen pops up, follow step 4 (4. On your input password...
  3. Replies
    4
    Views
    159

    [Misc] Re: Konica C224e MFP Reset Tool

    A Nuclear Bomb to fix a problem that a bullet could resolve...

    Try this thread first, this is the proper way to do it. Post the information found when doing the procedure outlined below into that...
  4. Replies
    7
    Views
    840

    [Error Code] Re: Bizhub C300i D073 error

    Just make sure to keep a good record of that change. Life sucks when you have to deal with a forgotten password.
  5. Thread: Error code

    by femaster
    Replies
    2
    Views
    353

    Re: Error code

    1) This is not the place for this.

    2) What's your point of reference? :confused: Codes can mean various things depending on the machine.

    3) Create a proper introduction post, then find your...
  6. Re: Toshiba 385s invalid factory configuration problem

    Give this link a try:

    https://www.copytechnet.com/forums/toshiba/
  7. Re: Replace Hardrive C458. and color patern on scan

    Minimum size drive would be 320GB. You can use larger, but needs to be at least that big.
  8. Replies
    11
    Views
    680

    Re: 504 Gateway time out

    No problems over this way the few times I've been on here throughout the day. US Midwest over here.
  9. Replies
    8
    Views
    541

    Re: konica minolta c250i unknown problem

    That is a shortened form of the default admin password and it will not get you into service mode.

    I can only assume that you are not a tech, so I will not provide you with the default service mode...
  10. Replies
    5
    Views
    451

    Re: Bizhub C224 - printing problem

    Based on the sample, definitely the belt as copyman stated. That is what one of the two calibration stripes look like after the cleaning blade attempts, but fails, to clean it off the belt surface.
  11. Replies
    5
    Views
    366

    Re: Shift image to one side

    Not just shifted, but it looks compressed as well. Not really sure what to say about that. I assume it happen with everything including prints and copies off the glass (not ADF)?
  12. Replies
    6
    Views
    615

    Re: Konica to olivetti drums

    One thing I know that happens when you change that switch is network settings get deleted. There might be some others as well, but I know network does for sure.
  13. Replies
    6
    Views
    485

    Re: C550i CE password

    That is curious. I've seen a similar error (MAC mismatch) on a machine that we had to change the CPU board out on. The error only showed up when marketplace was enabled, but didn't seem to affect...
  14. Replies
    3
    Views
    1,038

    Re: Service Manual workcentre 7232

    See previous post on the subject...

    Service Manual workcentre 7232
  15. Replies
    6
    Views
    485

    Re: C550i CE password

    Most likely the button they are talking about is holding down the power button on the control panel while flipping the main power switch, which forces the machine to boot into diagnostic mode.
    ...
  16. Re: C220 (Like C280 C360) issues with bypass and both tray 1 and 2. Jam but no paper

    When you get around to replacing those roller, also remove the black "oneway" bearings that the rollers interface with and look at the metal shaft under each of them. If it is really shinny, with a...
  17. Replies
    1
    Views
    1,351

    Re: c300i dog earing on double sided

    Maybe look into this and check to see if the front and rear side guides in the paper drawers are centered properly. We have fixed dog earring on a number of machines now by putting this adjustment...
  18. Replies
    11
    Views
    2,356

    Re: Bizhub C224e OPC drum

    That's rather cold. Typical room temps average around 72, +/- a few degrees.
  19. Replies
    4
    Views
    1,480

    Re: c654 JPEG Check NG

    HGST (Hitachi Global Storage Technologies) was actually a really good brand back in the day, prior to their acquisition by WD (Western Digital) in 2012.

    HGST - Wikipedia
  20. Replies
    11
    Views
    2,356

    Re: Bizhub C224e OPC drum

    We usually see that when there is an issue with the development unit. Based on your own admission, I'd have to guess it's because the wrong toner is now in the development unit.
  21. Replies
    4
    Views
    1,833

    Re: c3350i adf won't reset

    The only issue we have seen with the ADF on these so far is the tires not dropping down, but that has only been on 1 unit out of the 30 or so of this style that we have out in the field. That issue...
  22. Re: konica minolta mobile print: not finding printer with apple 13 iphone

    Not saying it is, not saying it isn't, but if I had to wager any money at all I'd say this is a Chat GPT response...

    It has already been established that AirPrint is not something the C220 can do...
  23. Replies
    7
    Views
    965

    [Misc] Re: Konica C450i Intermittent Paper Empty

    Great idea in theory, but in actual use it's a failure.

    What we have found is that customers generally only want to use special paper a few sheets at a time, and only on a rare occasion. If you...
  24. Replies
    11
    Views
    1,322

    Re: Brand new C450i with 3205 jam code

    We have found that a number of our machines were plagued with a dog-ear problem, on the rear side of the machine, which would subsequently lead to jams, especially on duplex. We found that on the...
  25. Replies
    14
    Views
    2,497

    Re: i-series Version 2 announcement

    This whole thread is about to become a moot point. They are phasing out the version 1 and version 2 fusers for an "Upward Compatible" version that will fit both versions of the i-model machines. See...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4