the machine was purchased with this df and worked with it until a week ago, and what happened for now just to guess, even the customer can not give me an answer when and how it happened
Type: Posts; User: copycommerce
the machine was purchased with this df and worked with it until a week ago, and what happened for now just to guess, even the customer can not give me an answer when and how it happened
and when scanning df behaves in the same idiotic way scanning through smb and copying works only from the glass, sheet by sheet
done, but the result is the same, I even changed the whole df with another and the result is the same I think there was an electric shock on the mains and I'm afraid there is a problem with the board...
still has a jammed message at the specified position
in test mode df works normally and with one-sided and two-sided movement of the sheet
in copy mode the sheet starts and stops after the first paper position sensor and does not reach the second...
initial release for copying a document the machine does not respond, then I open the left cover of the DF and load it, the message on the display is like a scanned and unsent document to a computer
yes we did, but it had no effect
On Bizhub C360 the taking of originals from DF-617 does not work (the sheet starts and stops). We replaced DF with another - and it does not work. In the service menu the DF test works correctly, the...
Hello
Where can I find a driver to Konica Minolta 8050 with controller Fiery x3e 50k-c for operating system windows 10 x86 because I can not find it on the Konica Minolta official site ?
...
Originally the problem was the machine could be not found as a "windows" scanner or a scanning program. but only as a printer.
The problem was was the board we changed from the same machine model....
Hello!
When i turn on the machine Develop Ineo 215 а Message appears "check scan mode" and red lights error
What could be reason to that and how it can be removed this message ?
Thanks!
I need help bizhub 283 has no movie data
can someone please upload a file
thanks
Those jams are for registration sensor and vertical conveyance. The whole section was replaced and that wasn't the cause of the misfeeds. Today is the first day without misfeeds it seems that the...
We replaced drum and starter in the beginning of October and then the misfeed started to show more dunno what common have the drum unit in the whole picture ...
Yesterday we replaced the paper motor...
Today we will replace the paper motor and print the management list to see if there are jam codes that don't appear. The thing is that the machine work around 300-400 prints/copies without problem...
Hello ,
We have bizhub pro920 that misfeeds from all trays , aways stoping in vertical transport without giving error message(only says to remove the misfeed paper). We have another unit right...
Alrdy tryed that but the display is still only lit with power LED on ...
It worked after removing both batteries on the MFP board..
thx
Hello ,
After unsuccesfull firmware change one of our Bizhub 420 stuck's on lit display only.Is there a way to reset the firmware to factory?
Hello ,
We have a couple of bizhubs 420/500 that have image cuting problem while copying non standart originals(like books and larger documents that need custom original size and zoom...
Hello ,
We have the following problem with box printing from bizhub 750.After evry 4 prints the machine stops for 5-10 seconds and then continues ( which is very annoying for larger scaned files...
Thank you.We was thinking that the problem is in the network configuration they use.The problem is that this is municipality and theyr I.T. department think that the machine should bound to them not...
Hello,
We placed one unit of this thing at a client.Every day arround 11.30 till 1.00 pm the machine starts printing alone large quanties of prints.
They all loke like...
Sometimes during copy process (1 original 20 doublesided copies,the first few are fine then there is only the first side and the back side is blank,then after few more the first side is blank the...
We gonna check that out,and if not try the firmware reload.
lol ofcourse is not selected :S