you are correct sir. I assumed it was proprietary. My bad
Type: Posts; User: mmechura
you are correct sir. I assumed it was proprietary. My bad
BlackCat,
Do you have access to parts? If so I am happy to order. According to everything I have been able to read, Also the carriage PWB and or main PWB may be suspect. I do not have access to...
Error 2F47
I am able to print in Service mode and have updated the firmware to Version 1.5 (the latest available) however once restarted normally I am still getting the error 03800500-2F47. ...
I am able to print in Service mode. Firmware on my IPF785 is up to date at Version 1.5 Cleaned the print head, any other suggestions?? Thanks for your help in advance.
Mark
Thanks for the heads up. Can you please tell me by my post if I am anywhere near current.
Checking to see if any one of you would be so kind as to provide me with any updated firmware that may be available for the DX-C400 current levels are:
ICU - Main 01.03.F0
ICU - Boot 01.00.F1...
How about a broken pressure release actuator. I had one on Friday. I'm still wondering why this happened. When I work the fuser by hand and the gears depress they "snap" into position which throws...
New issue, same machine - DX C400. On the rear side of scanning/copying only in full color mode only the machine is not aligning the colors properly. There are examples attached. Any ideas? The...
New issue, same machine. On the rear side of scanning/copying only in full color mode only the machine is not aligning the colors properly. There are examples attached. Any ideas? The issue is...
Thanks BC You are a wealth of knowledge and a huge help. Can you please tell me how to get into simulation on this machine. Thanks
Sure am, looking for some help on a Sharp right now, figured I'd troll around and see if I can contribute in some way.
I'd go with the sticky pad at the eject guide. The machine is feeding into Tray A - Stapling/Offset Tray the machine is putting the paper into the duplex unit for turn over. The guide being stuck...
Hi all,
I have a DXC400 that stopped printing, the machine is calling for black drum and developer. The customer replaced the drum unit, developer units seem to be back ordered nationwide. Is...
I would like to get availability, part numbers and pricing (if possible) for an eStudio 2830C paper lift unit or any parts that are available. The broken item is a driven gear that meshes with the...
I have a full complement of PCBs, motors and odd switches and such for a Kyocera 400ci, more than $1500 list. Looking to get rid of all of it
WANTED I am looking for a fax module for a Savin 4085 either new or used. Thanks in advance for your help.
Thanks alot teckat, I appreciate your help. I will be calling them in the morning. Is this a high mortality part?
I need a part #FS6-0129-000 (Gear 14T) and I was wondering how common that gear is on Canon machines, I have two Ir-C3200s in storage, can anyone tell me if that gear is present in that machine and...
you might have to find a used machine at a wholesaler, you can probably get one for less than $50. Good luck
Can anyone out there get me a couple of small parts for a Canon iR-5000? I need P/N FS6-0124-000 - Gear 24T, FS6-0862-000 - Gear 42T/14T/20T, FB2-6892020 - Holder, Switch. Thanks for your help in...
My client has one of these and is complaining about the waste bottle filling up too often. The current firmware in the machine is: [1.03 / G1395941C], Engine [20501700], NCS [4.17 / G1395932]. ...
I know this is probably a stupid question but can anyone help me with the setup of a document server for an Aficio 1224c. I have a client that recently aquired one and the Doc Server IP is set and I...
Can anyone please help me reset the admin code for a Bizhub 600 I need to change printer and scanner perameters. Thanks in advance.
Mark
I don't know what this is. Can anybody point me in the right direction? Any help is greatly appreciated, thanks in advance.
Sharp AL-800
Error code L 1
I am getting an SC865-01 which after searching this site and have found that the problem is the HDD's.
Can someone please talk me through the procedure for formatting through the Tech Rep mode. ...