Search:

Type: Posts; User: COPIERTEC ASSOCIATES

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. [Electrical] Re: Canon IR 3300 Continous Restarting

    I met this problem a number of times and the solution to this would be changing the power supply board or the RAM and the problem could be solved.
    Since these are old machines,the power supply...
  2. Re: irc2880i - insert drum cartridge

    I bet you will need a qualified tech to fix the problem on this particular model.However,this problem generally occurs from the HVT pcb which may need replacement depending on the age of the machine.
  3. [Dead] Re: Canon iRC 3025i does not access the download mode

    Try reseat the boot rom and the rams on the logic/printer board to clear the problem,it is more probable that the Boot ROM does not boot up the machine.
    also try to reseat the HDD and re start the...
  4. [Misc] Re: Reinstall Firmware for Canon iR 2016J

    please check your e-mail
  5. [Misc] Re: Reinstall Firmware for Canon iR 2016J

    I got this firmware for free from this forum through technical brotherhood and i give it for free send e-mail through ;atellellajames@yahoo.co.uk
  6. Toshiba e-studio 5520c cannot find hdd data

    Hello comrades , i have the above machine giving the error message above and i believe it could be a firmware issue. The purpose of this note is to request for assistance on this issue,thanks
  7. Re: e studio 5200 c cannot find HDD data

    You are actually right the model is e-studio 5520c,and gives the above error. could you be having the firmware within your achieves,thanks
  8. e studio 5200 c cannot find HDD data

    Hello comrades i have the above machine with error mentioned above,upon switching on the error cannot find HDD data props up any ideas appreciated thanks.
  9. Replies
    7
    Views
    3,990

    [Error Code] Re: E0004- 00102canon6570

    Try to check the IH power supply for possible dry joints and connections
  10. Replies
    7
    Views
    3,990

    [Error Code] Re: E0004- 00102canon6570

    I had a similar experience and did the following to overcome the error;
    1. check the thermistors if they are ok make sure they firmlly seat on the heater roller,however during the web drive the...
  11. Re: HP MFP178 nw ERROR ,REPLACE NEW TRANSFER BEL

    Thanks for the input actually the service manual has nothing to that effect.
  12. HP MFP178 nw ERROR ,REPLACE NEW TRANSFER BEL

    Hello comrades i have this printer showing the above error but continues to print.
    The purpose of this note is to request on any skill of how to reset the error message,thanks.
  13. Re: Need print driver for Canon D1120

    Which operating system of the pc does your client have
  14. Re: Canon bearing for IR6265 fuser pressure roller

    The bearings are readly available on market in my country
  15. Replies
    1
    Views
    326

    [Misc] Re: [canon] high capacity tray

    what do you mean by High capacity tray? However if it is the usual multi purpose tray 3,there is an adjustment screw at the extreme end that you are supposed to slowly adjust for the machine to read...
  16. Replies
    20
    Views
    1,408

    Re: IRA6055 Line on prints

    I would suggest you change the laser unit coz for your pdf even the test print shows the line.
  17. Re: canon ir-adv c5535/5540 firmware

    Thank you so much for the firmware and may God bless you and continue to guide you throughout you life.
    you have really shown a spirit of brotherhood.
  18. Re: Canon c850 skewing image on second side

    There could be poor alignement of the rollers on the duplex unit,check the springs and tensions in the duplex.
  19. [Misc] Re: canon ir6570 print blank and then "wait to print " on panel forever.

    Under service mode do a DC CON clear and re-start the machine ie COPIER>FUNCTION>CLEAR>DC CON,then switch off and on the machine.
  20. Re: Free Firmware IR and ADVANCE Machine

    May God bless and continue guiding yuo
  21. [Misc] Re: Canon IR 5000 exit roller replacement

    1. Do you have the new exit roller itself?
    2. If you have the shaft roller,pull out unit 1,at the exit there is a metal plate attached with 2 screws one on either side unscrew to detach the plate...
  22. Re: Canon IR 4235 with light copies

    The fact that the font report is ok ,it means the laser unit is ok.
    Try to clean the optical fibre on the scanner with a cotton wool or clean cloth with spirit.
    If the copy is still faint clean the...
  23. Replies
    3
    Views
    789

    [Jamming] Re: iR-ADV 8205 PRO

    Also try look at the sensor flags from the fixing to the duplex unit the may have a delay in getting back to the home position.
    Try to look at the selonoid play as it actuates the flapper.
  24. Replies
    3
    Views
    720

    Re: HDD canon

    Canon hdd can never be clonned you can only get the original canon hdd and install the firmware
  25. Re: canon ipf840 showing hardware error 03130031-4027

    Thanks blackcats i will do the needful and get back to you
Results 1 to 25 of 277
Page 1 of 12 1 2 3 4