Search:

Type: Posts; User: djbass

Page 1 of 5 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    9
    Views
    2,414

    [Error Code] Re: TOSHIBA e-studio 2505ac F090 error code

    1800 is pretty recent firmware (latest is 1900) so I don't think that's the issue. It's more likely to be something physical like a cable not seated properly or faulty hardware, there's no special...
  2. Replies
    9
    Views
    2,414

    [Error Code] Re: TOSHIBA e-studio 2505ac F090 error code

    It's very possible that whichever firmware you've applied to the machine is too old and does not support the USB WiFi module. That would also potentially be the cause of your F090 and F111 errors as...
  3. Replies
    3
    Views
    541

    Re: GN-4030 wi-fi module issues

    I haven't had that specific message, what I do know is that for 2.4Ghz connections the Toshiba WIFI won't operate on channels higher than 10. This creates a problem because most routers and access...
  4. Replies
    2
    Views
    929

    [Error Code] Re: Toshiba e-studio 5540 again...

    You likely have a charge/bias leakage issue (developer, main charge, transfer) that is causing the backgrounding and stripping developer material out of the dev tank (the stripping in the cyan colour...
  5. Replies
    31
    Views
    28,123

    Re: ES 7516AC error C471

    This issue was resolved in firmware version 1500 or higher that modifies some 08 codes related to temperature values, it was found due to variation in tolerance of the IH shield caused temperature to...
  6. Replies
    8
    Views
    1,273

    Re: 8508A, pops building circuit breaker

    I've had something similar where the IH coil was faulty due to breakdown of the insulation on the windings.
  7. Replies
    16
    Views
    2,975

    Re: Toshiba ES-5005ac jamming

    I see this problem a lot unfortunately and almost always results in an E011 jam where paper will stop right at the transfer belt because it is not rotating due to seized transfer belt cleaner...
  8. Replies
    6
    Views
    1,037

    Re: Toshiba estudio 2050c

    Those lines are definitely coming from either the main charge grid/electrode on the drum or the mag roller on the developer assembly, what I can't figure out though is why the lines are wavy.
  9. Replies
    3
    Views
    6,870

    Re: Scanning to PC - Toshiba E-Studio

    All of Toshiba's MFDs are intended to be network connected devices, that they support USB at all is more of an after thought.

    With that in mind you can print via USB but scanning via this method...
  10. Re: Toshiba e347csl squeaking loudly when printing

    The image drums on those start to seize up as they get old and it could be an indication one is on it's way out, easy to test by removing one at a time and closing the cover to see if noise...
  11. Replies
    35
    Views
    13,234

    Re: What copier is this in The Matrix?

    Canon NP 6035 would be my guess
  12. Replies
    7
    Views
    3,828

    Re: Opinions on laser theory, please

    I assume by calibration you mean you've done a laser excitation adjustment?

    I have seen something similar where the flat ribbon cable for a particular color is not properly seated.
  13. Replies
    2
    Views
    2,314

    Re: Purpose of the SRAM

    SRAM is a bit of a misnomer when it is really an EEPROM (though on older machines it was a battery backed SRAM).

    Toshiba devices use it to store important machine settings such as serial number,...
  14. Replies
    6
    Views
    1,543

    Re: Parts for inventory?

    I will echo the above, other than standard PM items the following are useful:

    HDD: Gotten better with the newer series but Toshiba HDD's will fail if you even so much as sneeze at them.
    ...
  15. Thread: ES 287 csl

    by djbass
    Replies
    9
    Views
    2,907

    Re: ES 287 csl

    To be fair it is a re branded OKI printer so not entirely Toshiba's fault. I always thought this series was ok apart from being somewhat messy inside and the ADF jam access cover always grinding...
  16. Re: eStudio 3540C not recognizing new toner cartridge

    Just for future reference toner cartridge detection is handled by two methods on this model.

    There is an IC chip on the back of the toner cartridge that internally has a counter, once this counter...
  17. Replies
    29
    Views
    26,609

    Re: TOSHIBA e-STUDIO455 Scan to E-Mail not workng

    How did you setup the Wireshark interface? It requires the laptop to have two networked interfaces in bridge mode (one to copier, other to network point).

    The 455 requires a USB dongle to enable...
  18. Replies
    29
    Views
    26,609

    Re: TOSHIBA e-STUDIO455 Scan to E-Mail not workng

    Stepping back a moment to what arnh79 originally said.

    There is a patch (not firmware) that has to be applied to firmware version 330 and above that resolves issues with gmail/office365 disabling...
  19. Replies
    29
    Views
    26,609

    Re: TOSHIBA e-STUDIO455 Scan to E-Mail not workng

    I forgot to mention make sure you test from the same network point as the MFD (had issues with restrictive firewalls or proxies mangling data before), though I'm assuming you did.

    I've also had a...
  20. Replies
    29
    Views
    26,609

    Re: TOSHIBA e-STUDIO455 Scan to E-Mail not workng

    This is the point I'd usually setup a network bridge on my laptop and capture the data with Wireshark to see exactly what's going on.

    As a process of elimination though and to isolate if it's the...
  21. Replies
    29
    Views
    26,609

    Re: TOSHIBA e-STUDIO455 Scan to E-Mail not workng

    Settings as per Google recommendations:
    Send email from a printer, scanner, or app - G Suite Administrator Help

    Enable SSL: Accept all certificates with CA
    SSL/TLS: StartTLS
    SMTP Server...
  22. Replies
    7
    Views
    3,698

    Re: Toshiba E Studio 4520c C970

    1. In my experience the process unit with the fault will usually have a thick coating of toner on the drum when you inspect the unit.
    2. If I recall, you can try unplugging each connector for each...
  23. Replies
    5
    Views
    2,178

    Re: Fax printing from a default tray

    If you mean output tray, normally it is set through 13 fax setting mode.

    13-930 set as follows:

    0 = inner tray
    1 = tray 1
    2 = tray 2


    Don't recall if its the same code on EBN devices.
  24. Replies
    2
    Views
    654

    Re: eBridge Next Control Panel

    It's a good idea but ugly solution, i usually advise them to usr the I icob on the scteen
  25. [Dead] Re: Toshiba ES 2550C Stuck at "Checking System, Please don't Turn off"

    HDD issues aside, try starting in 08 mode, then do a proper shutdown with the soft off button and restart.

    Sometimes if the machine isn't shutdown before power off it can cause that issue.
    ...
Results 1 to 25 of 114
Page 1 of 5 1 2 3 4