Search:

Type: Posts; User: strider5555

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Re: B005 Code on C258 | Same Fax Kit Works on other machines

    B005 error. FAX board error 5 (No fax board is installed. Mistake in installation, defective HW). I had this on a 4e series once. What ended up fixing it for me was plugging it into the Fax 2 plugs,...
  2. Replies
    22
    Views
    2,273

    Re: Bizhub C364e stuck on for bars

    Here is something to try from the KM knowledge base.

    Model: bizhub C364eCode: Display freezes at KM Logo, hourglass or Pillars (AKA: Shark Fins, Bars, Columns, Towers) Stuck at...
  3. Replies
    10
    Views
    1,069

    Re: Secure Print on a BH 300i

    If you login to PSWC, does it show the correct model? Or is it showing generic? I had a C450i do the same thing with secure print. Print driver showed all the correct options enabled, but secure...
  4. Replies
    6
    Views
    1,605

    Re: BH-4050 (momo), Admin password lock

    You could try this.

    Problem
    CE pasword/Service mode locked

    Solution
    CAUSE:To many failed attempts entering CE password

    SOLUTION: Perform a System Restore by following the...
  5. Replies
    15
    Views
    1,806

    Re: i series reset CE password

    Perhaps there is help for you in this other thread.

    https://www.copytechnet.com/forums/konica-minolta/162571-konica-c224-e-cant-access-service-mode.html?highlight=ce+password+reset+forum%3A40
  6. Replies
    15
    Views
    1,806

    Re: i series reset CE password

    I am unfamiliar with a 246i, however on the c360i series and possibly others, there is a known issue with the CE password change and being unable to access service mode. First you need to do the CE...
  7. Replies
    7
    Views
    1,201

    Re: Bizhub C3350i

    You could check the default subject and text are not blank. Also try a different send from address/admin address.
  8. Replies
    10
    Views
    1,218

    Re: Konica C450i Account Track

    Had a similar issue on a C450i. Could not get secure print to work. First it was because IT installed a B450i driver, but even after installing the correct driver it still didn't work. You need to...
  9. Re: Bizhub C3350i C-5372 CPU temperature errors

    Yes we tried replacing the fan on a few of these pos's but the error came back and ultimately had to replace the CPU board. I wonder if this has something to do with the fan noise reduction? Because...
  10. Bizhub C3350i C-5372 CPU temperature errors

    As the title says, I have had multiple C3350i machines with C-5372 codes. KM has no knowledge of this for this model, however the A3 size I series has a known solution that a firmware update fixes...
  11. Thread: Vcare Woes

    by strider5555
    Replies
    8
    Views
    680

    Re: Vcare Woes

    You could also try the Vcare connection checker app. You can download it from mykonicaminolta.com if you have access. load it on a laptop, connect it at the customer site, input all the connection...
  12. Replies
    4
    Views
    696

    Re: SD-510 Close Finisher Door

    I had this once on a 951 with FS532/SD. turned out that the fold motor took out the sd control board. Try disabling the SD and see if the message goes away. I ended up replacing the motor and board...
  13. Replies
    5
    Views
    700

    [Error Code] Re: Bizhub C368 showing C-D011

    CD011: Hard disk out of specifications mounted.

    Service manual says to replace HDD and logical format. Should be at least a 250GB hdd, but more commonly a 320GB is what is installed.
  14. Replies
    14
    Views
    1,930

    [Error Code] Re: bizhub C258 firmware

    Looks lite the sata firmware is already updated, you can try the recovery firmware GXX-A8, but that code says the HDD is not formatted, so step 1, check all hdd connectors, step 2 in service mode...
  15. Replies
    29
    Views
    3,498

    Re: C284 firmware error

    Not sure what else to try. I never had any issues other than what I mentioned. Try without the HDD attached, check that the machine type select information is correct, possibly format the SSD. Clear...
  16. Replies
    29
    Views
    3,498

    Re: C284 firmware error

    This may help. 58168
  17. Replies
    29
    Views
    3,498

    Re: C284 firmware error

    It should be listed under special firmware.
  18. Replies
    29
    Views
    3,498

    Re: C284 firmware error

    Roll it back to G00-72, then first load GB0-A9 version up firmware, then proceed with GR7-M0. Make sure to read the GB0-A9 firmware pdf, there are important steps to follow. Warning, the last time i...
  19. Re: Bizhub C458 - the purpose of the HDD and mSATA card?

    The 2.5 HDD is there for user boxes, as well as to store the address book, movie data, ocr font data, voice data, and is required if the machine has a fax, probably also needed for scanning (not sure...
  20. Re: C308 Incorrect size/type indicated PC215

    I should also add that I have also had this issue. Found out the hard way that the PC-110/210410 is the correct accessory
  21. Re: C308 Incorrect size/type indicated PC215

    The PC-115/215/415 are for the C458 series machines and are incompatible with the C308. Here is the configuration sheet for the C258/308/368
  22. Replies
    2
    Views
    1,457

    Re: Bizhub 227 - c -f907 error

    Maybe this will help.
  23. Replies
    26
    Views
    7,166

    Re: Bizhub C250i restarts

    I have witnessed, and reproduced the CPUB NG error when using the diagnostic recovery tool. I think it needs an update, because, i tested it on a C250i with N5 firmware and it reported everything...
  24. Replies
    94
    Views
    56,965

    Re: Konica Software Switch settings (complete)

    Here is a bulletin with all the intelligent yield control settings and models it works with. For the B227 it must have G3 or newer firmware, Function version 3.2. On 4/4e models it only works when...
  25. Replies
    6
    Views
    1,704

    Re: C300i C-FD8B ?

    Had this today for the second time. Today was a B300i, turned out to be the video cable for the second side scan was not fully plugged in at the baseboard. I'm assuming a setup error when the machine...
Results 1 to 25 of 95
Page 1 of 4 1 2 3 4