Sorry but thought I had replied but cant find it. I tried both 654 & 658 but no success. On starting up from scratch message was "install print cylinder". Also no green light on release button
Type: Posts; User: Philh
Sorry but thought I had replied but cant find it. I tried both 654 & 658 but no success. On starting up from scratch message was "install print cylinder". Also no green light on release button
On startup, display reads "insert print cylinder", which is already in position.
Cannot reinsert it as it will not pull out.
Green button remains unlit, even when pressed which makes no...
Can anyone advise me on the best way to replace the paper exit roller (shaft with 6 rubber rollers just left of heat fuser) Photo attached?54300
Paper elevator spring is #14 which shows as open ended. However I used the closed end spring for elavator as the open one fit better on the sector arm. Good news is that everything is back together...
Resending Attachmenmt
I took over from a repair job which was not finished. This involved paperfeed clutch in secondary feed. I have two springs, one of which should go onto sector gear, arm and the other onto U-shaped...
Following paper feed problems suddenly occurring where paper fed ok initially but jammed in second feed section. I tried checking out the paper feed clutch but after removing the eclip I could not...
This RP3700 had been working fine until today when I sent an Adobe Acrobat file over the network and the Riso responded in the usual manner, i.e., rejecting the old master and loading a new one etc,...
I have found the cause - At the delivery (receiving) end of the machine there are two black transfer sensor belts about 1/2" wide which are spring loaded onto a small shaft with guide pulleys. One of...
RP3700 was running fine and paper jam G256 code came up. As there was no obvious jam I turned it off and on a couple of times and it resumed printing but only foe a few copies. Same code displayed,...
What is the latest version of Windows able to interface with the RP3700. I am asking this as I am able to interface through PC with Windows 7,
but the 32 bit version. I have tried with Windows 10...
Re error codes. Started out with T17 020. Nothing jammed in unit but fuse kept blowing. Many more codes followed after this but I can't remember them.
I am in the process of dismantling a RP3700 which has under 1 mill copies but had error codes. I replaced this with another RP and would like to keep some of the parts from the old one, like boards,...
It is Riso oem ink, but I don't know mfg date. Surely though if the ink was bad I would have the same problem when I turn the image 180 deg?
I have attached scans of the blurry one along with the better one made with the document turned head to toe. Unfortunately the really blurry copies had been thrown away,
but at lease this should...
RP 3700 prints first few copies normally but following copies the print blurs and text fills in at the top of page where the heading is in 18 pt bold. This problem is resolved by making another plate...
You have got it right on when it comes to Riso. I also have a small print shop in Arizona and have had the GR3700 series and 2 RP 3700.The GR's copies were always wet and low res. I don't think I...
I have been considering purchasing one of these machines. It seems that Richo are offering them for about half their original listed price both here in US and Europe.
Obviously they can't have been...
I am 80% sure that my problem also lies in the disposal end of things but I had not considered a jam. Sure I had a master hanging off the cylinder but after removing it everything else in there...
I had posted earlier about not being able to unlock the drum etc. I found a blown fuse (F5) which is a 3.15 Amp . I replaced it with a 3.0 Amp as it was all I could get. Turned the machine on and it...
I am looking for a service tech to fix my Riso RP 3700 in Chandler, Arizona.
Forgive me if this sounds a dumb question, but when drum is hand turned how do I know when clamp unit is in "home" position? Drum "looks" in home position when compared with other undisturbed drum...
Clamp seems closed entered TM 552 = "Error TO1- 524. Nevertheless went ahead with TM 556 and drum released. There was a master hanging down off of it which I removed and then pushed in drum unit...
I have had problems with the master compression for a while but by starting out with an empty master disposal box after a few master misfeed messages have been able to get things working. I recently...
Many thanks for your accurate advice. When I thought about it, it made perfect sense but I would have to admit I would never have thought of it myself. I had not mentioned that the "paper" being run...