This post saved my can today. Definitely worth checking. Thanks, Lee.
Type: Posts; User: mattguthrie
This post saved my can today. Definitely worth checking. Thanks, Lee.
Replacing the HVT-PCB fixed the problem. Thanks to everyone who submitted a reply. Every little bit helps.:D:D:D
Thanks for the reply. What's causing the strange appearance at the end of the transfer roller? My poor photography skills! Sorry about that. The print is laying on a towel and I failed to crop it...
Ok. I am at the customer’s location. I replaced the drum assembly and cleaned the laser assembly, however the problem remains. I read on another thread that there should be a leaf spring on the front...
A reply! Awesome! Genuine toner is being used. I didn't have time to return to the customer yesterday but will be going back today. I will check the laser assembly. My only concern is that a dirty...
Good morning, everyone! As the title states, I have an IR2525 that is producing light prints. I have attached an example. The customer reported that the problem started last Friday morning and...
All is well now. AjitN's reply was the most helpful when he referenced the IDC sensors in the vertical conveyance section. The MFP is in a very noisy location and I can't always hear what kinds of...
Not always. My supply person gets what's available when it's available, so it is not consistently OEM.
Good Morning,
I have a C360 giving me C2552 and C2554 codes. These are high toner concentrations in the C and M developers. I've researched this problem on the site, but the info is often...
Thanks for the reply niceville. You aren't being vague at all. After talking to a local Sharp dealer, it is quite clear that this customer needs to move on and upgrade. The AR-FX7 has some innate...
I have a customer who cannot transmit faxes to certain numbers. Fax error codes include ERROR03 and ERROR07; I cannot find any of these in any service documentation. The MFP will dial and connect to...
Thanks Albonline. Your solution seems to be what cured the problem. I returned to the customer yesterday morning as I had said I was going to do in an earlier post. Upon arriving, the customer was...
Thanks for the reply Synthohol. I'm pretty sure I cleaned them when replacing the belt but have not tried a skew correction reset. I'm on my way back to the customer's location so will do a reset...
Thanks for the quick reply. The top IS NOT the lead edge.The right side is the lead edge.The problem is intermittent but seems to happen only on multi-page jobs.
Also, the orange looking lines in...
Good Morning,
I have a C451 with an issue I've not seen before. I have attached a pic. The registration at the top of the page is fine; toward the bottom it starts to spread out. I've changed the...
E
That is a very good question. Upon further examination, the solid color test pattern has some color in the defect. PH, MFB, firmware maybe? I just don't know where to start. Thanks for your...
Hey All,
I have a pattern that I don't recognize printing from a C451(see pic). It is obviously in the engine section but I'm not sure where to start. Hopefully the many experienced eyes that...
The retract clutch did indeed resolve this issue on the 7132. Thanks to all who responded to my help request.
I have a 7132 with a white band. See attached pic. The prob appears to be the same as the original post on this thread. Is this caused by the clutch mentioned earlier? This prob, too, is...
Thanks for the reply, Iowatech. You are not the only one with this suggestion. The source of the prob was a transfer belt image density sensor cover on the registration assembly that had become...
Hi,
I have a Bizhub C250 that is printing thin cyan lines across the whole print area. In the pics, the lines almost appear as a haze, but my camera will not capture them as they appear to my eye....
Hi All,
I have a Sharp ARM 355 that powers off when the ethernet cable is plugged in. Disconnect the cable and it works fine.
Thanks in advance for any suggestions.
You are absolutely correct, Mr. BC. Cleaned the wires in the assembly 4 times. No more probs. Thank you for your help.
Update: the problem was gone when we returned to customer's location this morning. Now it has light streaks across the page. I have included a sample. This device has just under a million prints on...
I have a Taskalfa 620 with this line running down the middle of the page. Please see the attachment. The prob started after installing a new toner. We replaced the drum blade but have no other ideas...