Search:

Anyone interested... PM me.
Kits, Developer, Fuser rollers, Drums, Blades, (No Toner) Many smaller parts added free.
PM me if interested in inventory (Still working on it)
Pete

Hey guys... haven't been around since Smarka disappeared. Still working on how this site works.
Appreciate your patience.
In dire need of firmware for the Toshiba 2830c series?
Trying to help out...

Will do, but seems strange that I "Duck Ducked" - "Toshiba eStudio 2830c Firmware" and this Discussion came up so I came here and posted.
It may be dead on the site here, but it's alive out in the...

Did anyone ever send James the firmware for the Toshiba 2830c series? Trying to help out a race track in Arizona with their old ES 2830c.
My email is pwalter1953@gmail.com if anyone can send the...

Hey guys
Is this just the nature of the beast? It does not have a legal size glass bed. But it will copy legal through the DF and pull from a legal tray. Yet it will not scan a legal to PDF or...

Used to get these at Precision Roller. Then I began using "Stix All" in the tube. Just carefully laid it on and gave it 24 hours cure... Worx great if you can still find it. Made by Elmer's.

I'm in AZ. Might be able to send someone by.

What range are you looking for? I have a bunch of P2035s and a few others.

Entered at 33 but it was on the IBM Selectric typewriter... and lately that's what I'm back to doing at 67, 34 years later... Typewriters! Still helping out the folks that need me, though.:cool:

Canons have no developer.
It seems to be a charging issue. The toner mag roller is perfect until the drum unit pulls toner in that horrible pattern. I guess that would suggest the drum unit. Wish I...

Been using Katun since 1980s. Haven't for awhile , but their quality never was an issue.

Here's what I found. Not sure if the above techs fixed it so thought I'd send this.



Code: E027-0400
Description:Error in supply with Bk Developing Assembly
Failure in detection about the...

If you've got another unit laying around you might try swapping these units mentioned below. Otherwise, You should probably move on.
Causes:The wiring is faulty (short circuit, open circuit). The...

Just rebuilt drum with Drum and Blade. (Not Charge Roller) Copies were great.
Copier in very unstable location with potential power issues, but have had Mita, Savin, and Toshibas there over the...

Not sure I understand...
..."should be rebuild firmware if the HDD fault".

Toshiba eStudio 2830c
Powers up, Lights in right side upper corner of panel light up, but no display.
Worked on Tosh for years but have been away for some time doing Canons. Do these op panels...

It seems the Drum Drive PCB is not the board with the four sensing devices on it. Am I correct here.
Manual showed a grouping of boards and the DDPCB seems small and in a different location than...

Was Thinking That Might Be The Case.

QUESTION: How should I approach this? Replace each wheel and each reader or just go with the whole pcb?

I've got numbers and prices on the readers and...

I'm thinking a flipped blade would be highly evident on any copies that do get through.The copies look fine when it prints.
Cleaned the encoders twice to no avail.
Short of beginning replacement...

I cleaned all four discs and reader slots twice. Once using canned air, second time using a small brush with air again.
It still goes into E0000-0206 after a few copies.
Could the encoder discs be...

At the risk of sounding a bit moronic... need a bit of guidance. This is my only unit like this in the field.
It seems the Tech pub modification will fix this, my only question is where to find the...

Canon IR Adv. C5030 / Ser# GNG35555 / Total Prints 240,415
Copier located in Prescott, AZ Mountains. Hard to get to. Need help before I go.
This code returns or changes between 000012 -0206 and...

Hello Folks! Trying to help a church out here. Giving them this giant.
Runs great. Fuser good but noisy.
Has three issues.
1. Seems to have intermittent blur lines where the image is slightly...

Would have if I'd had them. Just keepin' the oldies going. I live 1 hour from PR. Know them personally. If my posts annoy you, ignore them. Just coming over from over twenty years at Smarka. Chill!

Does anyone have the three gears off the Heat roller gear on this (Canon IR400) unit?All the gears on the backside of my customer's are either chipped or worn down. Thet can be good used if you've...