Also, dusting increases when the air is too dry. When I have problems with dusting, I install a moisturizer machine to get the humidity up to around 30-40%
Type: Posts; User: impetus73
Also, dusting increases when the air is too dry. When I have problems with dusting, I install a moisturizer machine to get the humidity up to around 30-40%
I have the same problem. Did you ever find a solution?
Hi.
On Ricoh MPC 3002, a typical scan filename when scanning to email, is: "201607261208.pdf", while on 2800/4501/3003, it's "20160726120832652.pdf"
If you scan 2 or more files inside the same...
I keep getting this page, when clicking on forum posts:502 Bad Gatewaynginx
Yep, 90% of the time, the customer either pushed the tray into a wall, or placed a table or stacks of paper boxes under the tray, and when the tray moves down, it's stuck, and fails.
So you force the copier to work 24/7, and complain it's loosing focus? I think every copier deserves a good night sleep, like the rest of us to stay focused! :-D
Swapped a pump with a used one with another colored toner inside of it? Are you crazy? :-0
When I get pale prints on those machines, and ACC fails because of it, I manually adds toner using SP 3015, you sometimes have to run it twice or more, to get it good.
I suspect the cause of the...
If the toner bottle is rotating, and toner is exiting the hopper unit, into the dev unit, then it must be the dev unit that is not rotating, or blocked or broken toner feed coil.
To check the...
If it's possessed by the devil, then you need to install the "Exorcism SD card V2" in the lower SD card slot, and press "Start Exorcism" on the menu. :-D Then burn the card afterwards.
Seems like old copiers still works on 9 of 10 computers! :-D
It's an very old model, what driver are you using, and did you try the latest firmware available for that model?
What program is the...
I don't know this model, but on the AF1027 I had to tighten the two long springs that drags the lift plate up, as they get loose over time.
Just cut off a few rounds of the spring, and make a new...
If the jam happens at the same stripper every time, remove the stripper permanently. You only need 2-3 strippers in a 5 stripper set, for it to work :-D
If we made a muslim fee zone, we would be sued for racism, for sure... odd how that word mostly is a one way phenomena...
Only solution, is to setup a laptop next to the machine, and allow them to print from the laptop using a memory stick in the USB port of the laptop.
I don't see what the VM card is needed for, but you will need the USB card, and a USB/SD host extension, that you mount on the side of the operating panel. Not sure if MPC4500 has this, or if it was...
Press the yellow physical key, then 107, then press and hold the grey/brown C button for 4 seconds.
The fuse goes as shown in the pictures:
2956429565
The shovels inside the toner hopper unit, is notorious for getting bent, so they don't shovel enough toner out of the hopper unit. Dismantle it, clean it and bend the shovel plastic guides (4 of...
Normally, to enter special mode, just press and hold # when entering the Sp menu. Not sure for the printer versions though...
Odd, but true... how quickly one forget :-D
WD-40 works perfect on rubber rollers, it do feel counter-intuitive, but so do quantum mechanics :-)
Try WD-40 and you get a better life. The rollers does not dry out, and they get a perfect...
Use WD-40 to clean the rollers, and sep pads.
You can scan to any email address you want in the whole world.
To get scan to email to work, make sure the firmware is the latest, then you need the following info:
Customers SMTP server,...
There is nothing wrong with the universal driver, might be if your still using v3 or early 4, but I have had no problems with 4.6.0.0
If you installed a new sleve unit, then the fuse is in the box you tossed away. It's taped to the bottom of the sleeve's card board box. Check the trashcans :-D