Search:

Type: Posts; User: makutzi

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    739

    Xerox 1000 Jam Error 77-941

    Hi All

    On our Xerox 1000 we are getting a constatnt paper jam error 77-941. The entire day!!! It prints about 3 pages and then the error appears - -I tried just about every thing - short of...
  2. Thread: DL DiagPC tool

    by makutzi
    Replies
    1
    Views
    748

    DL DiagPC tool

    Good Day All

    Am lookign for the DL Diag PC tool - used to make some diagnostic tests on the Xerox ESS PWB - it captures a log file with information. Also looking for the Fuji Xerox NVM...
  3. Replies
    2
    Views
    3,567

    Re: Error 116-321 on C75

    I switched the machine off and on several times. Also at the Main switch. Still same error. I cant seem to be able to get into any menus on it. I switches on and lights flash and within seconds it...
  4. Replies
    2
    Views
    3,567

    Error 116-321 on C75

    This morning when I switched the trusted C75 on I immediately got Error 116-321. I was out of the office for a few days and think that the machine was on when the power tripped. What could have...
  5. Replies
    14
    Views
    7,703

    Re: Biz C308 Admin and Service Password

    Sorry, not related to the actual priblem just the comment made...Love the last paragraph - I should try that with my Xerox machine...
  6. Replies
    3
    Views
    2,358

    Re: Xerox 1000 Diagnostic tool

    The original PC UI was corrupted with the Hard disk (due to power problems). Installed a new PCUI but with it came the Xerox Diagnostic tool which only works for 10 days then one needs to get license...
  7. Replies
    3
    Views
    2,358

    Xerox 1000 Diagnostic tool

    Hi All

    A while back I was looking for the diagnostic tool called PC Diag for our X1000 press. No one seems to have heard of it as all referred me to the Xerox Diagnostic tool. We had to re-install...
  8. Re: Colour issue (banding/arcing) on Xerox C75 Press

    Problems solved: Got a new Dev housing - the gears were somewhat worn out - and away went the banding issue.

    Thanks you for the input
  9. Re: Colour issue (banding/arcing) on Xerox C75 Press

    In searching I found a previous post "Error 042-326" dealing with this error - can reset it with NVM 741-132 set to 0
    Tried and its booting up - now the dev unit change and test...
  10. Re: Colour issue (banding/arcing) on Xerox C75 Press

    Machine is cleaned out and the exit tubes are all silver clean. There is a bit of wear on the rollers of the dev housing. I swapped the cyan with the magenta housing yesterday and the problem...
  11. Colour issue (banding/arcing) on Xerox C75 Press

    Hi All, hope someone can offer some help...

    Have a C75 which is working like a charm. Recently we had a grinding noise coming from the back on and off. I was away and my colleague printed a big...
  12. Replies
    2
    Views
    3,189

    Re: KM Bizhub C8000 Spare Parts

    Hi, sorry what is the FD and the GP-501? Oh golly, yes shipping to the states would probably kill the deal.
  13. Replies
    2
    Views
    3,189

    KM Bizhub C8000 Spare Parts

    Hi, I have two KM C8000 machines standing in our yard destined for the scrap yard. Have salvaged two fusers (second fuser units EF101) from it which are still in good condition. Does any one need...
  14. Replies
    14
    Views
    4,341

    Re: C75 won't duplex

    Hi, I had the same issue on our C75. Checked all and cleaned it all, but it still did not duplex. The i tightened the tooth belt which drives the duplexing unit (long belt) it seemed to fall off at...
  15. Replies
    3
    Views
    3,352

    Re: Xerox dc242 drum reset

    Hi, would this also work on the C75 Press?
  16. Replies
    8
    Views
    4,089

    Re: Xerox C75 Grinding noise

    Hi All

    Problem solved! Removed the Deve drive assy (CMY), opened up the gear and belt system, cleaned all out, gave it a good wiggle and reassembled it. Built it back in and voila, only a few...
  17. Replies
    8
    Views
    4,089

    Re: Xerox C75 Grinding noise

    Good idea, however I did check it and all was clean and fine. Thanks
  18. Replies
    8
    Views
    4,089

    Re: Xerox C75 Grinding noise

    I found IT!!!!

    Did 093-018 Deve motor and the noise was there
    093-020 - also
    093-023 Perfect
    093-024 Deve YMC - noise was back

    Distinct gear grinding etc. So will probably have to replace...
  19. Replies
    8
    Views
    4,089

    Re: Xerox C75 Grinding noise

    OK found the codes i wanted: did the following checks and all worked out fine and no noise from them:
    042-200 ITB belt home sensor (low)
    010-010 Fusing motor - perfect
    042-001 Main motor - perfect...
  20. Replies
    8
    Views
    4,089

    Re: Xerox C75 Grinding noise

    Its not the Duplex gears, its coming from the back of the machine, or the inside back, more or less where the fuser is situated. The duplex problem was fixed when we replaced the drive belt of the...
  21. Replies
    8
    Views
    4,089

    Xerox C75 Grinding noise

    Good Morning

    We have a Xerox Color C75 which is working really great for us. A few weeks ago we noticed a slight grinding noise coming from the back every now and then. It has now escallated and...
  22. Replies
    11
    Views
    3,079

    Re: Xerox C75 Duplex problem

    I also noticed in the error log the last error shown was 077-130 and 077-129 - not sure yet what they are but think they relate to the duplexer problem.
  23. Replies
    11
    Views
    3,079

    Re: Xerox C75 Duplex problem

    So, I opened up the tray, removed the parts to be removed to gain access and as it turned out the belt of duplexing thing had slipped off, which was causing the grinding noise. That fixed, tried to...
  24. Replies
    11
    Views
    3,079

    Re: Xerox C75 Duplex problem

    Hi, thanks for the hint. will do. Thanks for the tip.
  25. Replies
    11
    Views
    3,079

    Re: Xerox C75 Duplex problem

    Hi, thanks for the tip, just got a service manual and checked out the procedure to remove the mentioned parts. Thanks again, will definately give it a go.
Results 1 to 25 of 58
Page 1 of 3 1 2 3