Search:

Type: Posts; User: Woxner

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Re: C3070L - faded white diagonal stripes on thick paper, only on yellow color

    replace the yellow developer. you can try and tone up but it may be shot. i would start with new drums and dev for all colors. one can affect the other. make sre toner port is not clogged
  2. Replies
    2
    Views
    120

    Re: Bizhub 4052 c5501 error code

    had to replace a power supply for this. i was getting fuser codes. replaced the fuser then a week later the c5501
  3. Re: C308 unresponsive touch screen everywhere except CE mode

    firmware has been known to fix this. also backup HDD and do logical formate
  4. Re: Reason I haven't been around for a little while

    Sorry for your loss. Prayers are with you.
  5. [Dead] Re: Konica Minolta bizhub C360 attacked by overzealous security officer

    Ck you pm message
  6. Re: Black lines ONLY on Color prints C368. FIXED but still curious about symptoms.

    cl the idc sensors and run reset reinialize in stablizer then gradation then stableizer. i see your colors are out of alignment. this fixed it for me. how much on drum units? start simple.
  7. Replies
    5
    Views
    368

    Re: Kon/Min Firmware

    I was told at school is has the prev as well not just the fix
  8. Re: B758 Jamming 9201/9202/9203/3201 Double sides

    repl the reverse unit past the fuser. bearing slips
  9. Replies
    4
    Views
    307

    Re: i Range usb export not working

    This sounds silly but did you scroll up on the screen to enter password. These like the 3.1 flash jet drives.
  10. Replies
    14
    Views
    2,297

    Re: Konica Plotters?

    Km does not sell kip anymore. We use HP. Most kips are pretty good if in right place. I had some in or close to welding shops. They turned out to be a pain in the ass. Coronas were always a problem...
  11. Replies
    26
    Views
    1,844

    Re: I-Series storage board & boot problem.

    There is a way to format these storage boards. You need a code.
  12. Replies
    13
    Views
    1,472

    Re: Bizhub 368e smearing

    There is firmware for this issue. You also have to change a dip switch as well. Problem only happens after it sits.
  13. Replies
    5
    Views
    458

    Re: DR314K vs DR313K

    The 8 series will fit the 8e with no mech problem. It will however not last as long. Maybe 50 to 70% life. The 8e does not work in 8 series
  14. Thread: cE301 on C250i

    by Woxner
    Replies
    19
    Views
    1,185

    [Error Code] Re: cE301 on C250i

    if you can turn off market place this causes problems, soft sw 172 set to 01 also turn off in admin mode. i had this problem on a c360i. i did manage to get 45 to work. had to just let machine sit...
  15. Re: Konica 1250 toner piles on charging unit sides after 5000 copies

    perhaps the transfer belt is not transfering all the toner also replace transfer belt rollers. 951 does same thing.
  16. Replies
    4
    Views
    336

    Re: c364e firmware upgrade

    Open the folder and transfer all the files in the folder to the root. Nothing else on the usb.
  17. Replies
    9
    Views
    639

    Re: BH650i half black copies

    Ck for 8 series bulletin on this simular problem
  18. Thread: kmbs 658e

    by Woxner
    Replies
    2
    Views
    276

    [Error Code] Re: kmbs 658e

    update firmware and replace home sw for scanner
  19. [Misc] Re: I series stopping at 25% of the boot process

    its B6 now or 6B. there is a procerdure to reset the storage bd reqiures a code and you need to run the 8 series tool. it will wipe all meters. to tewst if its this bd take it out and see if you can...
  20. Replies
    10
    Views
    1,176

    Re: i series reset tools

    and the 8 series reset tool is used for i series as well
  21. Replies
    10
    Views
    1,176

    Re: i series reset tools

    one way to test storage board is to remove it and see if it will load firmware. it wont load controller though
  22. Thread: i series

    by Woxner
    Replies
    10
    Views
    1,787

    Re: i series

    for marketplace to be totally off set soft sw 172 to hex 01
  23. Replies
    9
    Views
    725

    Re: KM c654e Scan Issue

    run the adf chart for mag size and skew. i had one two days ago that only did this on email scans. copies were fine
  24. Replies
    6
    Views
    550

    [Dead] Re: Konica 458E wont turn on

    repl mfp and possible eemcb. had this many times
  25. Re: Brand New Bizhub C300i - Connection Failed window pops up every 5-10 minutes

    turn soft sw 172 to hex 01. also turm market place off in iws tab in admin.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4