Search:

Type: Posts; User: orestesp

Page 1 of 2 1 2

Search: Search took 0.20 seconds.

  1. Re: C280 ADRF Skew + Machine thinks magenta toner bottle is full

    I finally found some time to work on the bizhub.

    Updating the firmware to the latest available version didn't change anything, guess I'll just run it till the TCR sensor does its thing.

    As for...
  2. Re: C280 ADRF Skew + Machine thinks magenta toner bottle is full

    Forgot to add: The total counter on the machine is 130,000.
  3. C280 ADRF Skew + Machine thinks magenta toner bottle is full

    Greetings,

    I have run into some minor problems with our newly acquired bizhub C280.

    The first being that the ADRF introduces a skew (see .pdf file attached). Without wanting to prejudice you,...
  4. Replies
    1
    Views
    316

    Aficio MP4001/5001 Firmware

    Greetings!

    We have a Aficio MP4001 and a MP5001. The System/Copy FW version reported is 1.00 for the MP5001 and 1.01 for the MP4001 (see : MP4001/5001 Firmware Version - Album on Imgur). I am...
  5. Replies
    8
    Views
    611

    Re: C223 Paper jam in ADF unit

    Clean all the rollers on the ARDF that are accessible to you with no disassembly required with a damp paper towel. Use a compressed air can to remove paper dust from the inside of the ARDF. If the...
  6. Replies
    32
    Views
    2,440

    [Jamming] Re: Aficio MP5001 No feed jam

    Replacing the rollers (pick-up, feed & separation) fixed the problem.

    Thank you to everyone who took the time to reply.
  7. Replies
    2
    Views
    501

    [Misc] Konica Minolta Broken PCB Connector Fix

    Greetings,

    I came across a broken PCB connector while installing the FS-524 on the C280, and this is the way I fixed it. The solution seemed pretty obvious, but it still may be helpful to someone....
  8. Replies
    3
    Views
    253

    Re: Konica C220 error c171 and c186

    The only way to get your hands on the firmware files is either through a KM dealer or someone who has access to KM's partner network and can download the files for you.

    If you contribute to the...
  9. Replies
    3
    Views
    253

    Re: Konica C220 error c171 and c186

    See: https://www.copytechnet.com/forums/newreply.php?do=newreply&p=546008



    Firmware updated fixed the issue for the person who made the original thread.
  10. Replies
    5
    Views
    395

    Re: Bizhub C353 giving streaky prints

    It looks like the toner isn't getting fused to the paper properly.

    Have you set the tray to the correct paper setting?
  11. Replies
    24
    Views
    1,451

    [Error Code] Re: Konica Minolta accurio print C2060L error

    Try accessing the controller following what the manuals says: Accessing PageScope Web Connection
  12. Replies
    24
    Views
    1,451

    [Error Code] Re: Konica Minolta accurio print C2060L error

    From what blackcat4866 said, this print controller has 2 seven segment LED displays side by side somewhere on the controller (usually found on the back of the controller or on the motherboard) that...
  13. Replies
    32
    Views
    2,440

    [Jamming] Re: Aficio MP5001 No feed jam

    Hi tsbservice,

    I knew before making this thread that the rollers were most likely the culprit, but after doing some reading on the forum on Ricoh MFPs on no feed jams, there was sometimes more to...
  14. Replies
    32
    Views
    2,440

    [Jamming] Re: Aficio MP5001 No feed jam

    Like I said, I initially used water to clean the rollers, and when that didn't work, I used WD-40, which was recommended to me by a tech when asking for advice on how to clean the rollers when no...
  15. Replies
    32
    Views
    2,440

    [Jamming] Re: Aficio MP5001 No feed jam

    The PM table on this particular manual has no other mention of the paper feed rollers apart from the one page that I posted. I did try water+paper towel, and when that didn't work I used WD-40, which...
  16. Replies
    32
    Views
    2,440

    [Jamming] Re: Aficio MP5001 No feed jam

    I very much did, as I mentioned in my original post, and it has no mention of when the rollers need to be replaced. See picture attached.

    Imgur: The magic of the Internet



    Hi, thank you for...
  17. Replies
    32
    Views
    2,440

    [Jamming] Aficio MP5001 No feed jam

    Greetings,

    We have a Aficio MP5001 with approximately ~1,200,000 clicks on it. It was bought used, and basically every consumable (e.g. OPC drum, charging roller, etc) was, assuming from how bad...
  18. Replies
    19
    Views
    1,468

    Re: J-7229/J-7217/J-7216 & Both Sides Adjustment

    Mark, you were spot on; it was that solenoid. I opened up the finisher and I found that the stopper was bent inwards in order to get the proper clearance, as the manual suggests. The solenoid...
  19. Replies
    19
    Views
    1,468

    Re: J-7229/J-7217/J-7216 & Both Sides Adjustment

    Finally for the ADU sag. Do I have to take off the fuser + the ADU and tighten the screws that attach the rails to the main body, or is there an easier way to do this?
  20. Replies
    19
    Views
    1,468

    Re: J-7229/J-7217/J-7216 & Both Sides Adjustment

    I finally found some time to work on this problem a little bit more. After some head scratching and some trial and error, I've finally got it to duplex within the 1mm tolerance.

    The chart...
  21. Replies
    19
    Views
    1,468

    Re: J-7229/J-7217/J-7216 & Both Sides Adjustment

    I printed the job that I was printing before and did a comparison. It's pretty much the same. I cleaned all the ADU and registration rollers (idlers with some IPA and took the glaze off as you...
  22. Replies
    19
    Views
    1,468

    Re: J-7229/J-7217/J-7216 & Both Sides Adjustment

    Hi,

    I will be cleaning the rollers on the registration section as well as the ADU, try again, and report back with my results.

    Just a quick question that might seem a bit naive; do the hard...
  23. Replies
    19
    Views
    1,468

    Re: J-7229/J-7217/J-7216 & Both Sides Adjustment

    Thank you for replying.





    Like I said in my first post, the problem is now gone. The jamming was only present when I set the paper to exit from the main tray of the finisher. The exact same...
  24. Replies
    19
    Views
    1,468

    J-7229/J-7217/J-7216 & Both Sides Adjustment

    Greetings,

    I have, yet again, ran into two problems while printing with the C6500. I will outline each one in detail down below, thank you to anyone who takes the time to read through this.
    ...
  25. Replies
    12
    Views
    1,113

    Re: IC-303 System and User Software ISOs

    I was never asked, and there is no Win XP label anywhere, just a Win XP embedded sticker with no serial number on it.

    I'll just stay put then. Thanks.
Results 1 to 25 of 48
Page 1 of 2 1 2