Search:

Type: Posts; User: tulintron

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    172

    Re: C71HC Image Fault

    You can print the separate colors and measure the distance between the marks. I would shoot drums or developer units.
  2. Replies
    4
    Views
    171

    Re: C7000 with C4603

    Check life of consumables, check sensors are clean, check skew adjustment of color lasers (mechanical adjustment near laser window).
  3. Replies
    4
    Views
    171

    Re: C7000 with C4603

    Can you post a photo of test pattern number 80?
  4. Replies
    4
    Views
    380

    Re: Bizhub Pro 951 Weekly Timer Unable

    It's grayed out and I can't change it

    In Setting Data, I copied the data from another 951 next to it and it continues the same problems.
  5. Replies
    4
    Views
    380

    Re: Bizhub Pro 951 Weekly Timer Unable

    It is. But without permission to touch. Hidden. Wiped out. Disabled.

    I don't know how to use the correct expression in English.
    As if there was some function not allowing it to be available to...
  6. Replies
    4
    Views
    380

    Bizhub Pro 951 Weekly Timer Unable

    49456Bizhub Pro 951.


    [Please enter desired copy time/ 0 hour(s) 05 minutes] message


    Weekly timer setting appears unable in Administrator Setting. Help

    Operation Procedures for Weekly...
  7. Replies
    3
    Views
    136

    Re: C6500 Exit Section Causing Smudging?

    Toxic is right. This issue occurs with heavy media. Marking happens on the second transfer as the end of the paper comes off the registration roller. This causes media vibration and interferes with...
  8. Replies
    7
    Views
    316

    [Misc] Re: KM Documentaion USB Drive

    I am willing to contribute a portion of this amount and see how much knowledge will help me. In your place, I would help active contributors to this forum. Contributors in information, in help.
  9. Replies
    11
    Views
    1,409

    Re: KM C224 Non "E" Control Panel Question

    It only needs the firmware that makes the numeric keypad appear on the panel of the NON model And the same appears on the E models. I've seen this before but I don't remember the firmware. If I find...
  10. Replies
    1
    Views
    132

    Re: movie data firmware

    Check your PM's
  11. Re: Develop ineo+227 (Konica ) error code c-2152

    Between the belt cleaning unit and the waste toner container there is a small plastic piece that makes this connection.
    It may be the cause of toner solidification.


    With the cleaning system...
  12. Replies
    3
    Views
    179

    Re: Konica C8000 press finisher problem

    Enable DIPSW 11-7 to ON to show J-xxxx. It is easier to locate the error.


    Try other paper formats.
    Try heavier paper weights.
  13. Re: Develop ineo+227 (Konica ) error code c-2152

    How did the error occur?
    Did the printer work and stop?
    Was it after maintenance?
    Is the printer electrically protected?
    Just replaced the belt or ITBU?
  14. Replies
    13
    Views
    448

    [Misc] Re: C654e trouble.

    We have knives with molds from various parts of the printers. We cut and replace.
  15. Replies
    13
    Views
    448

    [Misc] Re: C654e trouble.

    I had. We do this constantly in our laboratory. Drums, blades, coronas and new developers. We recorded the chips. Everything is right here.
  16. [Misc] Re: Problem when print front and rear in A3 paper

    I agree with Synthohol. Stop the print and see where the problem occurs. Photo of the problem sheet would not be bad
  17. Replies
    1
    Views
    115

    Ricoh Pro 5100S

    Good afternoon friends. As everything in life has its first time, I am here humbly asking for help. I really need the Ricoh Pro 5100S service manual.

    Thanks for any help
  18. Re: Original left on glass or detecting A4 with no paper C368

    I honestly prefer to believe in coincidences. Scan Area does not interfere with original size. It only changes the margins on a millimeter scale. In our laboratory we have several machines with...
  19. [Misc] Re: Pro 951 vs Pro 1100 UFR's and thermistors

    We already tried 951 in 1250, also without success. The diameter is different. It may be your problem.
  20. Re: c360 wont copy or print. Machine comes to ready

    Did the connectivity test through the ping command at cmd prompt?


    Did you print the driver test page?


    What is the status of the front LED on the touch panel during job submission?


    What...
  21. Thread: Bizhub 808

    by tulintron
    Replies
    9
    Views
    312

    Re: Bizhub 808

    A simple question, but it can solve:


    Did you perform the trouble reset?
  22. Replies
    3
    Views
    177

    Re: Konica c360 turn on jam codes

    When entering System 2, go to 2nd page
  23. Replies
    3
    Views
    177

    Re: Konica c360 turn on jam codes

    49156
  24. Re: Strange prints think developer might be empty

    Target shooting!
  25. Re: Original left on glass or detecting A4 with no paper C368

    Good. Here in our laboratory we have already exchanged the complete scanner table. Very simple removal and would discard many doubts. I agree with Emujo2 to be related to CCD. This sensor on the...
Results 1 to 25 of 437
Page 1 of 18 1 2 3 4