Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Re: Any machine with the Internal Finishers...

    Bizhub c224e, FS533 (internal finisher) stacking/offset sort issue.
    =^..^=
  2. Re: Any machine with the Internal Finishers...

    Any specific MFP, any specific internal finisher? There are a lot of posts on this, at least as it applies to the 4e series. =^..^=
  3. Replies
    11
    Views
    527

    Re: Kyocera Ecosys 6535- Pauses

    A couple of our techs were losing the spring consistently, during the roller change. =^..^=
  4. Re: Kyocera dp-7100 jam 6910(sub code 01)

    I've had a bad punch PWB cause the finisher to act strangely. If you have a punch you might try powering OFF > disconnect the punch > run U906 > and power back on again to see if it changes your...
  5. Replies
    11
    Views
    527

    Re: Kyocera Ecosys 6535- Pauses

    I think the spring he's referring to is the spring on the pickup roller/feed roller assembly. It presses the pickup roller down against the paper stack.

    50203
  6. Replies
    3
    Views
    325

    Re: keep safe FIRMWARE

    AFAIK if the techs can't copy the USB stick, neither can the MFP. If you don't trust your techs maybe you should have different technicians. =^..^=
  7. Replies
    3
    Views
    325

    Re: keep safe FIRMWARE

    Who are you trying to keep the firmware safe from? Do you have a firmware thief ransacking your PC?

    =^..^=
  8. Replies
    9
    Views
    367

    Re: ADI HDD and SATA HDD

    This is your third post on the same topic. Do you think that if you keep asking, that you'll get a different answer?
    I'm done answering since your not too interested in the replies. =^..^=
  9. Replies
    12
    Views
    584

    Re: C-3110, E-304 and E-301...

    You might treat it like you would a non-print data issue:

    Change the IP address
    Check for correct print drivers
    Check for correct print emulation
    Check for duplicate IP

    =^..^=
  10. [Misc] Re: Default Setting for "auto drum refresh"?

    The drum refresh process is intended to remove condensation from the drum surface. It's performed at initialization, waking from sleep mode, and when the humidity sensor triggers it. I personally...
  11. Re: Kyocera Fs-2100dn unable to connect to PC

    I'd suspect that the USB connector is damaged on the main PWB. Did you try connecting via the network interface?

    And no, it's not a dedicated driver. The Universal will work, if it's able to. ...
  12. Replies
    12
    Views
    584

    Re: C-3110, E-304 and E-301...

    Error Signal Reception

    E301: Referring incorrect memory
    E304: Finished due to error outside Qt library

    I did a little reading about Qt, but honestly I have no idea where Qt is integrated on...
  13. Replies
    12
    Views
    584

    Re: C-3110, E-304 and E-301...

    Did you mention what model that you were referring to? =^..^=
  14. Re: C-458, "Unable to connect to Authentication Device"...

    Once you're in service mode > enhanced security mode: Stop 0 Clear > User Authentication > OFF.
  15. [Misc] Re: Konica Minolta C258 custom paper tray seting

    Here's the DIPSW's that I can trace back:

    10 02 04 ???
    25 Firmware Function Version 3.0: 40, to firmware function version 4.2: B0
    51 Consumable Life Warning-do not show: F0, to display all: 00...
  16. [Misc] Re: Konica Minolta C258 custom paper tray seting

    Thanks for posting back, and collecting the appropriate data. We can work with that to narrow it down further. =^..^=
  17. Re: HP laser jet 4 plus printing checks with Data faction program, not registered cor

    I'm good, thanks.



    All true. Maybe slower, but never faster paper passage.



    And you would see line blurs crossfeed, where the fuser was pulling the unfused paper faster than the latent...
  18. Replies
    1
    Views
    171

    Re: 5520C firmware

    That won't help your "Service Recommended for SPC" message. =^..^=
  19. Replies
    3
    Views
    242

    Re: 5520C error code. Service SPC

    Start by cleaning the drum potential sensors. Details on pg 1447 of your manual. =^..^=
  20. Re: HP laser jet 4 plus printing checks with Data faction program, not registered cor

    Sounds like BS to me. I can't imagine any fuser changing the image registration, as long as it's the correct fuser.

    Laserjet 4+, eh? Probably a museum. I'm surprised that any kind of print driver...
  21. Re: Kyocera dp-7100 jam 6910(sub code 01)

    I can be pretty sure that the J6910 has nothing to do with your document processor. J6910 is a finisher jam on the 4000 sheet finisher. Its a rear DF (hence: document finisher) side registration jam....
  22. Replies
    1
    Views
    203

    Re: main board Ta 3510i

    You'll probably have a C-0840 greet you at bootup, and/or "Time for Maintenance T".

    Observe the qualifications about replacing the main PWB:
    swap the original EEPROM onto the new PWB at YC14...
  23. Replies
    25
    Views
    1,645

    Re: FK-8550 Shortage

    I'm looking at U346 in the manual, and I don't see anything called "fuser power mode".

    I do see:
    Timer/Sleep Level: BAM conformity country setting
    Auto Sleep: Switch auto sleep function setting...
  24. Replies
    10
    Views
    582

    Re: Ta 6052ci scan color way off

    Your memory is good. =^..^=
  25. Replies
    10
    Views
    582

    Re: Ta 6052ci scan color way off

    This might look familiar. Mine turned out to be a ISC PWB and calibration:

    Wanna see some cool copies?
    =^..^=
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4