Search:

Type: Posts; User: Blizzoo

Page 1 of 20 1 2 3 4

Search: Search took 0.30 seconds.

  1. Replies
    6
    Views
    270

    Re: connection lost e-maintenance

    Disconnect one working machine and use that static ip address to your problem machine, if working then you know who must fix it
  2. Replies
    11
    Views
    490

    Re: konica and ineo

    Analog machines still exist and do copies :)
  3. Replies
    24
    Views
    1,028

    [Misc] Re: Ricoh 6054 Printing question.

    Perhaps there is a some kind of setting/quota in equitrac causing this or does the job is logged as a complete job in equitrac logs?
  4. Replies
    3
    Views
    126

    Re: Oki C531 printer

    Hi, check if the belt is ok not stuck or something interfering with belt motor, check Fuser Unit if ok and turning, check the LED's under the top cover are in the correct position especially the...
  5. Replies
    31
    Views
    1,270

    Re: Scan and translate paper documents

    Wish you success Mister Sales Man!
  6. Replies
    10
    Views
    350

    Re: OKI MC561 black stripes

    Yes swap the units and see if the defect moves with the unit. Fro the pictures it seems that the dr blade is the issue here. Use original toner as well.

    Normally these units are not serviceable...
  7. Replies
    31
    Views
    1,270

    Re: Scan and translate paper documents

    So you find the perfect app in the end? Or you already knew about it and now you just promote it here after scoping what else everybody have to say?
  8. Replies
    31
    Views
    1,270

    Re: Scan and translate paper documents

    test
  9. Thread: eb50

    by Blizzoo
    Replies
    5
    Views
    349

    Re: eb50

    Adjusting that separation spring tension helps with this double feeding. Decrease the tension a bit more as blackcat said for a better separation, you will probably see the separation roller getting...
  10. Replies
    4
    Views
    302

    Re: es5560 hdd erase

    I usually do a Factory Default in User Functions->Admin-> scroll down and hit Factory Default. Customer data is all erased also network information/scanning etc, no need to realod any FW. Never used...
  11. Re: Printer properties sometimes not accepting changes..

    Stupid question, have you removed/reinstalled the shared print driver on the problematic PC? Scrap any V4 drivers these are useless
  12. Replies
    6
    Views
    336

    Re: Toshiba E studio 5008A password forgotten

    Use it for parts, it's gone
  13. Thread: 8508A, E011

    by Blizzoo
    Replies
    6
    Views
    399

    Re: 8508A, E011

    Been in a fight with this jam issue on a 6550c and nearly got me :). Like your colleague said when testing, the belt turned but it doesn't turn normal. The screw holding the gear driving the belt...
  14. Replies
    5
    Views
    337

    Re: E457 reset counter to 0

    If you want to keep a track of printing usage setup Department Codes and here you can count the colour scanning jobs on a BS MFP your example estudio 457
  15. Replies
    11
    Views
    474

    Re: Konice C368 Transfer Belt Reset

    Wouldn't the print quality adjust to the best possible based on the readings of the used belt, assuming is still in a good condition, after the life counter is cleared? Or it need another calibration...
  16. Re: 2540c Showing 0% Toner and Asking to Install New Toner but Toner Still Full

    Or it may be some toner dusting over the toner drive section on M and K and most likely over the toner circuit board under those contact springs. To get there you need to remove all process units,...
  17. Replies
    2
    Views
    350

    [Error Code] Re: Toshiba E-Studio 2051c Firmware Update

    You may need the FW for the SSD insted of HDD regarding that signature issue
  18. Replies
    6
    Views
    488

    Re: 6560c ADD TONER CONDITION FOR BLACK

    If your K sub-hooper is full of toner then may be a loss of drive to the K sub-hooper (not feeding to the dev unit) side and it may be a case of just to properly clip back in the whole sub-hooper...
  19. Thread: e409S

    by Blizzoo
    Replies
    12
    Views
    914

    Re: e409S

    Well that sucks if an app must be installed for scanning...
  20. Thread: e409S

    by Blizzoo
    Replies
    12
    Views
    914

    Re: e409S

    You need to navigate to apps in EWS and from here go with Scan Centre Network Folders to setup scan to folders.
  21. Replies
    7
    Views
    397

    Re: Load LT-R and press [START]

    Thanks fort that
  22. Replies
    3
    Views
    323

    Re: Estudio 3508A printing issue.

    If the machine is setup to receive only Hold jobs or Private/Hold jobs you will get a similar issue as you described. Look into Top Access in Printer section somewhere in the top list there is a drop...
  23. Replies
    7
    Views
    460

    Re: Turning off APS ES-2508A

    Easiest way to do it is to create a Copy shortcut on the Control Panel. Select the Copy Screen, select the tray/any other settings you want to be defaulted in copy mode and the press the Home icon...
  24. Replies
    32
    Views
    1,548

    [Error Code] Re: E Studio 5055cse Dumping developer

    Testing the lamps can be done with all the parts inside, just cheat the front door interlock switch and front cover open/close sensor and don't leave the lamps On for a long time. You should have a...
  25. Replies
    32
    Views
    1,548

    [Error Code] Re: E Studio 5055cse Dumping developer

    If you get C380 right after the developer initialization I would suspect the ATS sensor. The top of the ATS gets scored in time by the wiper blade on the auger and can fail. In the picture attached...
Results 1 to 25 of 489
Page 1 of 20 1 2 3 4