Search:

Type: Posts; User: repn1999

Page 1 of 13 1 2 3 4

Search: Search took 1.29 seconds.

  1. Replies
    4
    Views
    150

    Re: Sharp MX3640 fuser noise

    They are brand new units from sharp and they have been tested in other machines where they work fine. Client runs health care type forms and no bleed to speak of just mostly bw text. Very rarely even...
  2. Replies
    4
    Views
    150

    Sharp MX3640 fuser noise

    So I have a mx3640 that continues to build toner and make the screeching noise like the web is locking up. I have confirmed that the client is not running machine out of spec or heavy coverage or...
  3. Replies
    6
    Views
    354

    Re: MX M453 "Remove paper from offset tray"

    replace the tray height sensors...i believe there are 3 and check the harness to the paper detect sensor on the tray. if the harness is not routed correctly it can get stretched and will cause that...
  4. Re: Looking for MX-3140n Firmware/Manual - HDD Replacement

    I just deleted some. Message me if you need to.
  5. Replies
    20
    Views
    1,381

    Re: MX-3610 color and calibration problem.

    Dumb question....Did you happen to check the density on the print and copy settings and make sure they are on defaults? I had a tech who wouldnt change out supplies and reset the counters...and when...
  6. Replies
    7
    Views
    637

    [Error Code] Re: MX4071 PHOENIX II SERIES E7-90 codes

    I would recommend replacing the Mini EMMC (smaller MSATA) card. I have seen corruption issues on the new eMMC drives on most of the new models unfortunately and have replaced several. I would also...
  7. Replies
    5
    Views
    315

    Re: MX3140 Desk unit trouble with some trays

    I know the issue is resolved from a previous post...but I would strongly recommend replacing all sensors in the feed units ANY time you have an issue whether that sensor is effected or not. This is a...
  8. Replies
    7
    Views
    623

    Re: MX6070N not keeping network settings

    I would say try a CN update with the latest version of firmware. IF this is an older MX6070 check the label on the MSATA drive on the MFPC PWB. IF the label says lower than v4.0 firmware I would...
  9. Replies
    8
    Views
    305

    Re: MX-M363 background and poor image

    I would say try swapping the dv unit. Your pic isnt the best but looks to me like lines/voids that match the surface of the dv unit are in the background. may have a dv unit rotation issue....I have...
  10. Re: Looking for MX-3140n Firmware/Manual - HDD Replacement

    I have them. I also have SD card images for this series. Please advise whether your machine has a data security kit on it or not. I need to know this before I provide any software so you dont end end...
  11. Replies
    2
    Views
    2,343

    Re: Sharp tech needed Northern California

    Are you still looking for a Sharp tech? I would be willing to relocate for the right opportunity. I am factory trained and fully certified on all current models. I was also a master tech regional...
  12. Replies
    3
    Views
    358

    Re: Sharp MX-M654N

    Excellent machine.....recognized among all manufacturers as a top performer and robust beast in the segment. Pretty technician friendly....stay up on the maintenance and you will be fine. My machines...
  13. Replies
    12
    Views
    786

    Re: Sharp MX-M753n

    Like the other guys have said, these are older but built like tanks. All of the dragon series was...and now the newer taurus series (mxm754,mxm6750) continue the durability these machines were known...
  14. Replies
    3
    Views
    240

    KIP 7100 wide format parts guide needed

    does anyone have a kip 7100 wide format parts guide they can hook me up with? thanks in advance
  15. Replies
    17
    Views
    2,517

    Re: Interesting find: Msata cards

    [QUOTE=bigdaddyooo;1435100]


    First I was addressing the comment someone made about swapping msata cards from another machine. Second....the reason you are having to CN update the cards is...
  16. Re: DSPF 2 to 2 lead edge is way off side 1 only

    so this only happens on side 1. can you reproduce the same random position issue by scanning from platten glass, since side 1 is read from ccd. if so then that would rule out dspf mechanical and...
  17. Re: fn-18 intermittently stops in saddle stitch

    I know this is gonna sound elementary but I would double check to make sure the machine and finisher are level (just because the plastic looks level it may not be. some machines may have to look not...
  18. Re: Scanning to google one drive and sharp OSA

    side note...you have to be an AIP connect integrator to get the applications for the phoenix 1 machines (3070, etc) but the phoenix 2 machine connectors are on the machine itself of available for...
  19. Replies
    17
    Views
    2,517

    Re: Interesting find: Msata cards

    I would like to point out something most have overlooked in this discussion....Machine specific meta data is stored on the msata card...and sd card on the older models. I do realize that some have...
  20. Replies
    3
    Views
    321

    Re: MX-M550 jamming issues

    I would replace the black guide on the left door and in the vertical pass sections. you can usually see where there is wear on the black guide on the lower part of the left door...the vertical pass...
  21. Re: Sharp MX-4101n error F1-00 finisher error

    which finisher does it have? I can get you a part number for the harness. FYI this needs to be fixed cause those models are prone to blowing boards from the disconnecting of finisher harnesses with...
  22. Replies
    5
    Views
    1,581

    [CQ] Re: Mx-m264n F2-64 error

    I tend to agree with all posts so far. I have seen DV units go bad as well as toner tubes getting clogged. OEM toner only on these. Aftermarket toners generally cause over/under toning and require dv...
  23. Thread: MX-60 toners

    by repn1999
    Replies
    1
    Views
    732

    Re: MX-60 toners

    They do not work
  24. Replies
    4
    Views
    1,553

    Re: MX-3060 with trouble F2-70

    I was going to suggest the bulletin as already noted by another tech but also....remember to shake the toners when they are put in. People tend to store toners on their end and they cake up. Can...
  25. Replies
    3
    Views
    1,510

    Re: MX-3071 jams TRAY2 / C1PFD_N2

    make sure to do the 50-10 adjustments for the trays since these dont have 50-28. tolerances are 4mm and 2mm. basically they should be the same on each side and the opposite matching those...
Results 1 to 25 of 301
Page 1 of 13 1 2 3 4