Search:

Type: Posts; User: tnrtt

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: 5560 CE40

    by tnrtt
    Replies
    12
    Views
    606

    Re: 5560 CE40

    Problem was the logic board.
  2. Thread: 5560 CE40

    by tnrtt
    Replies
    12
    Views
    606

    Re: 5560 CE40

    I've ran into the block problem several times. Super glued them and a layer of epoxy after. Works great. Always the black for me. Closer proximity to the fuser, Heat stress I guess. Not my problem
  3. Thread: 5560 CE40

    by tnrtt
    Replies
    12
    Views
    606

    Re: 5560 CE40

    I have an intact 5560 trade in. I'm going to take the process unit, transfer belt unit, Logic board and laser unit with me. I'll let you know what I find. Thanks for your help.
  4. Thread: 5560 CE40

    by tnrtt
    Replies
    12
    Views
    606

    Re: 5560 CE40

    Drums and developer rotating. Didn't check if transfer was rotating, my bad. Laser shutter worked in test mode. All that aside, I'm wondering why can't I get in to 04 mode and why I have a completed...
  5. Thread: 5560 CE40

    by tnrtt
    Replies
    12
    Views
    606

    Re: 5560 CE40

    Nothing on the belt
  6. Thread: 5560 CE40

    by tnrtt
    Replies
    12
    Views
    606

    Re: 5560 CE40

    None, BC. Didn't pull belt until I tried to enter 04 mode per troubleshooting steps. Don't understand why it wouldn't go in to 04 mode, yet ran a successful 05-2742.
  7. Thread: 5560 CE40

    by tnrtt
    Replies
    12
    Views
    606

    5560 CE40

    Checked 08-2528 to 2531. All zeros. Checked 05-2731 all below 628. Set 08-2486 and 2561 to zero. Go in to 04 to print test pattern and it throws CE40. Checked developer and transfer belt springs....
  8. Re: Oki CX3535T / Toshiba E studio 3540c CA00 Error Code

    Most of the time I've had that code on one of those, it's been from the transfer belt cleaner disengaging.
  9. Replies
    1
    Views
    226

    MJ-1112 CB95 code

    Had a chewed up ribbon cable. Replaced it and got the code. Replaced stacker motor home position sensor. Stacker motor drives past home position. I'm not getting 5 volts cn8 pin 5. I think it's the...
  10. Replies
    6
    Views
    313

    Re: MJ-1112 ribbon cable

    Not to beat a dead horse BC, but I plugged the number in my search on my manual. It appears you have to buy the plate it's glued on. Luckily Toshiba has one in stock. Just one.
  11. Replies
    6
    Views
    313

    Re: MJ-1112 ribbon cable

    Thanks. I'll check it out. Looking at it right now on FYI. Still don't understand why I couldn't find it in the tech to go parts manual
  12. Replies
    6
    Views
    313

    Re: MJ-1112 ribbon cable

    Thanks a lot blackcat. Where did you get that image? My parts manual is from FYI, looks nothing like that.
  13. Replies
    6
    Views
    313

    MJ-1112 ribbon cable

    Been through the parts manual four times and can't find the ribbon cable that connects the SDL and main PCB's. If someone could give me the page and item number, I'd appreciate it.
  14. Thread: counter reset

    by tnrtt
    Replies
    13
    Views
    1,442

    Re: counter reset

    It's a piece of cake. After you've stripped it to the frame and replaced everything, I'll let you know.
  15. Thread: MJ-1112

    by tnrtt
    Replies
    4
    Views
    386

    Re: MJ-1112

    It will do this at idle. It's like the stepper motors are get a forward and reverse signal at the same time. When going to make a copy through the finisher, the entrance motor just starts chattering....
  16. Thread: MJ-1112

    by tnrtt
    Replies
    4
    Views
    386

    MJ-1112

    I have this finisher on a 7506AC. When the covers are closed,the entrance motor, exit motor and transport motors are locked up.
  17. Replies
    0
    Views
    168

    Parting out 5540 serries copiers

    circuit boards, drive units, basically everything.
  18. Replies
    4
    Views
    1,037

    Re: E-Studio 55,65 & 7506AC

    I have three of them in the field. Two of them have blown the duplex open/close sensor. Other than that, they've performed flawlessly.
  19. Replies
    1
    Views
    1,297

    6570C developer setup

    Went to change K developer. Went to 05-2404 and hit start. Copier showed 2424 and went in to an idle mode like it was calibrating. Tried 05-2400, 2401, 2402, 2403. Same thing. Had to manually load...
  20. Replies
    6
    Views
    1,081

    Re: Need firmware for e-studio 3530c please

    RADF height adjustment. Had the same problem on a 4540
  21. Replies
    0
    Views
    680

    Panasonic DP-C405 fuser unit

    I have two brand new fuser units in the box. Make me an offer.
  22. Thread: estudio 6570c

    by tnrtt
    Replies
    10
    Views
    1,354

    Re: estudio 6570c

    Sorry Blackcat. Since this thread was directed at you, I should have realized you'd want more information than that.

    The whole story from the beginning. Customer was getting feathering in their...
  23. Thread: 6570C jamming

    by tnrtt
    Replies
    7
    Views
    1,049

    Re: toshiba 6570

    You're right. Tried new post from my cell phone and screwed it up. We determined it was the pre printed stock. Brought stock back and it did the same thing on our office machine which is an identical...
  24. Thread: estudio 6570c

    by tnrtt
    Replies
    10
    Views
    1,354

    Re: estudio 6570c

    What did I miss? The machine is telling me there is a problem with the developer. Multiple developers and units. I may have double posted this. You're the last person I want to get on the wrong side...
  25. Thread: estudio 6570c

    by tnrtt
    Replies
    10
    Views
    1,354

    estudio 6570c

    Failing cyan developer set up. Tried multiple developer units. Swapped EPU pcb with the last one. No help.
Results 1 to 25 of 103
Page 1 of 5 1 2 3 4