Search:

Type: Posts; User: GIUBOSS

Page 1 of 19 1 2 3 4

Search: Search took 0.02 seconds.

  1. [Misc] Re: Scanning ID or Large Document on Ricoh MP C2051

    copy ID card, go to 1 Sided + Combine 1 Sided button and set the full size percentage. Place the document in the 'ps corner, flip the document after the first scan in the same position.
  2. [Misc] Re: Ricoh MP C400 - Intermediate Transfer Unit is not set correctly

    would you like to say that you have tried another transfer unit taken from a working machine and it is not the same? Have you checked the attachment points and the connector if it is positioned...
  3. Re: Canon IRC 5560i. Mac Drivers only print double side

    you have also installed the PPD
  4. Re: Canon ir ADV C5240i randomly, when scanning and copying the first pages are black

    try to replace the cable between scanner unit and reader controller
  5. [Jamming] Re: Paper Jam in Right Door, even when there is no paper Canon IR3300

    there is a flag sensor in the register, sometimes it does not switch correctly due to the spring
  6. Replies
    1
    Views
    212

    Re: Lexmark XC2235 exit noise

    rubbing noise can be caused by drum cartridges that have been stationary for too long
  7. Thread: Aficio Mpc2500

    by GIUBOSS
    Replies
    3
    Views
    357

    [Jamming] Re: Aficio Mpc2500

    condition of the fuser unit? Damp paper can be more annoying in duplex mode.
  8. Thread: Ricoh mpc 5501

    by GIUBOSS
    Replies
    11
    Views
    597

    [Jamming] Re: Ricoh mpc 5501

    yes, this is one of the models, but I believe that the problem does not depend on this sensor, which delimits the maximum level of paper in the output tray.
  9. Thread: Ricoh mpc 5501

    by GIUBOSS
    Replies
    11
    Views
    597

    [Jamming] Re: Ricoh mpc 5501

    What jam error does it indicate? Try with the bridge unit installed by unplugging the finisher, it should work but it should indicate finisher error.
  10. Replies
    20
    Views
    806

    Re: Document Server missing

    have you tried to see from the web
  11. Replies
    1
    Views
    182

    [Misc] Re: Oce Colorwave 500 Toner Blobs

    The only alternative is to replace the black cartridge.Good luck!
  12. Replies
    5
    Views
    252

    Re: Xerox Workcentre 7120

    going to exclusion, the cyan developer remained
  13. Replies
    9
    Views
    450

    Re: ricoh mpc 3002,

    If I remember correctly it is the same procedure as in the previous models
  14. Re: Anyone has the OKI ES8473 MFP PPD linux driver?

    Look for a driver of another similar model with PPD and try.
  15. Re: mpc2800 pressure roller cleaning roller (unit)

    if replaced regularly, otherwise it is almost useless
  16. Replies
    1
    Views
    166

    Re: Code c-c163 bizhub C353

    Do you have the service manual? Wrong model firmware error during initial engine diagnosis.
    Defective EEPROM or PRCB.
  17. Replies
    8
    Views
    236

    Re: Bizhub C552 background

    If drum and development units ok, it could be the MFP board.
  18. Thread: Kyocera

    by GIUBOSS
    Replies
    3
    Views
    291

    Re: Kyocera

    The question is what problem did you encounter before removing the electronic board and the ram? Anyway firmware, ram ultimately replace main pwb.
  19. Replies
    18
    Views
    1,157

    Re: IMC3000 NVRAM zero counter

    It can happen when you load a damaged firmware, or some technical magician changes all the standard passwords.
  20. Re: Firmware language display RICOH MP C4503/C5503

    also have the same firmware Operation panel D1471490G or updated both ??
  21. Re: Firmware language display RICOH MP C4503/C5503

    Then update the operator panel, I haven't found the language firmware.
  22. Replies
    18
    Views
    1,157

    Re: IMC3000 NVRAM zero counter

    Ok, but I also suggested that you take the new nvram.
  23. Re: Firmware language display RICOH MP C4503/C5503

    try to change the switches in setting sp 5-009 to display the desired language (if preloaded in the machine)
  24. Replies
    18
    Views
    1,157

    Re: IMC3000 NVRAM zero counter

    Writing the procedure here would be irresponsible as well as illegal. The problems are not always solved by resetting the nvram indeed it could be worse. It is more appropriate to buy the new one.
  25. Replies
    7
    Views
    633

    Re: IR1435 faint copies

    did you clean the laser, original toner etc?
Results 1 to 25 of 452
Page 1 of 19 1 2 3 4