Search:

Type: Posts; User: Albonline

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    15
    Views
    454

    [Misc] Re: C3350i and marketplace

    each mfp is licensed/registered with km. the newer machines will only show a license management error on the lms screen.
  2. Replies
    15
    Views
    454

    [Misc] Re: C3350i and marketplace

    FYI no km app will load without the unit having a valid license.
  3. Replies
    15
    Views
    454

    [Misc] Re: C3350i and marketplace

    yes like c250i as far as os architecture.
  4. Replies
    15
    Views
    454

    [Misc] Re: C3350i and marketplace

    did you reset the base board before you booted the machine up ? the sn differences signify two different speed units. (you would have to have put the id board in with the base to end up with what...
  5. Replies
    15
    Views
    454

    [Misc] Re: C3350i and marketplace

    yes, to the base board actually base cpu id and ssd are involved in the licensing. check the sn's of the scanner and adf and main body. you may need to get an initialization code.
  6. Replies
    54
    Views
    15,250

    [Dead] Re: C250i does not boot...

    i have used generic raw(unformatted or partitioned) 256 nvme ssd's. if any i series unit is running any pre 2.0 firmware the ssd will become corrupted, and tagged as bad by the mfp, i have reused...
  7. Replies
    9
    Views
    487

    Re: Konica c280 crooked copy

    did you run the adjustments with the adf adjustment sheet? if not do so.
  8. Re: Why are my magenta prints Faded in one side? konica c360

    As i said b4 get a genuine konica developer unit. install it according to the service manual instructions, doing all suggested adjustments. then monitor the toner level history. the hopper may be...
  9. Replies
    10
    Views
    511

    Re: Bizhub C227 error C-3925

    check the heater lamp for open also.
  10. Replies
    6
    Views
    427

    Re: C454e unable to change Authentication

    remove the au device and the driver for it.
  11. Replies
    10
    Views
    511

    Re: Bizhub C227 error C-3925

    reset and be reliable won't happen.
  12. Replies
    9
    Views
    487

    Re: Konica c280 crooked copy

    I've only seen it once but the idler rollers in the turn guide , the spring broke leaving one side without pressure. adf ran sef 8.5x11 on up with no problem. but shorter paper skewed on the last...
  13. Replies
    10
    Views
    511

    Re: Bizhub C227 error C-3925

    thermal fuse smoked in fuser. they call it a thermostat but getting it to reset and be reliable won't happen.
  14. Re: Why are my magenta prints Faded in one side? konica c360

    if its going through new km factory units I would be looking into toner density levels. if you are simply reloading your old developer units i would try a new km unit. this line of mfps was noted...
  15. Replies
    26
    Views
    1,419

    Re: Blurry Barcodes on Plastic

    looking at the image i see what was at one time referred to as ac blowout in the plastic area. how to combat it in these series? no clue, (you may try setting to a lighter stock) but you say some...
  16. Replies
    26
    Views
    1,419

    Re: Blurry Barcodes on Plastic

    you are asking for trouble if you increase just 2nd xfer, the latent image is used as lube for belt cleaning blade.
  17. Re: Why are my magenta prints Faded in one side? konica c360

    That would have been your mag developer peeling. (fuser not hot enough to melt iron) if it was ending up on your paper, the belt cleaning system took a whole lot of it.
  18. Re: Develop Ineo+258(Konica Minolta B. C258)tray 1 and tray 2 need a lot of power to

    look at the white locking rods. they get worn. also check frame where they rub for burring.
  19. Replies
    6
    Views
    414

    [Electrical] Re: C250i Won't Power On

    that reaction from the machine is usually a short or a blown up board. if equipped with a 704, try removing the ds board, try with side door open. also if it was running fw 45 or earlier the ssd is...
  20. Replies
    26
    Views
    1,419

    Re: Blurry Barcodes on Plastic

    "In a nutshell" you are going from a drum to paper unit to a transfer belt type unit, you can increase coverage density via service mode adjustments(raising toner density,1st&2nd
    transfer voltage...
  21. Replies
    4
    Views
    305

    Re: external memory

    you may have to run the board reset tool. Then do just the mfp firmware.
  22. Replies
    2
    Views
    301

    Re: Konica minolta c8000 fuser jams

    Full bleed ? what kind of coverage are you doing?
  23. Re: konica minolta bizhub c552 wrong colors when printing (color conversion error?)

    did you uninstall and reinstall the driver?
  24. Replies
    30
    Views
    2,616

    Re: C308 SSD Board Replacement / Availability

    yes ,and monitor the toner density for a few hundred prints, followed by a full gradation adjustment.
  25. Replies
    30
    Views
    2,616

    Re: C308 SSD Board Replacement / Availability

    machine data on the 8 series mfps. is stored in at least 3 locations the emmc the flash roms on the mfp/driver board combo(once in each section) and counter/life on the removable roms. if 2 of the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4