Search:

Type: Posts; User: RMC8112

Search: Search took 0.01 seconds.

  1. [Misc] Re: Ricoh 2555 PCL printer partial page printing (JPG)

    I had something like this happen to one of my customers. Turn out to be the transfer roller. The foam roller was cracked. Once i replaced it, it printed perfect.
  2. Replies
    11
    Views
    587

    Re: MP501 VOID Area

    Ive seen this before. Check the drum unit, and charge roller. The cleaning blade for the drum has something stuck and is wiping the toner from the drum. When i had this happen to my customer, i took...
  3. Re: HP Pro M426dw original not exiting all the way gets stuck with about a 1/2 inch t

    If you look where the originals exit, there should be 2 black belts or bands. I had to replace the whole ADF section to fix that. There is no part number for just the rubber belts. Part no....
  4. Replies
    3
    Views
    303

    Re: MP C3003 sc 480-0

    i googled the error code and it says its the drum cleaning motor for the black.
  5. Replies
    7
    Views
    1,596

    Re: HP P3005 13.01 from tray 2

    I agree, however, I just clean off the foam pad and all the sticky stuff off. Then i wrap electrical tape around where the foam was, about 3 turns. Ive done this to many printers and no issues.
  6. Thread: blank in black

    by RMC8112
    Replies
    12
    Views
    661

    [CQ] Re: blank in black

    I ran into a similar issue with a MP C5503 and found that one of the gears was chewed up. I would remove the black PCDU and check the gears.
  7. Replies
    10
    Views
    873

    Re: Ricoh Mp2501 ( Too light copy problem

    Check the transfer roller. Ive seen this before and when i checked the transfer roller, there was a crack or tear on the roller.
  8. Replies
    2
    Views
    619

    Re: HP Laserjet 600 M601 swing plate

    its not too bad. first time will take you prolly 1 to 2 hours. ive done 4 so far and it gets easier. 46001
  9. Re: P3015 13.05.00 feeds blank sheet prematurely, from both trays. not solenoid

    Ive seen this before. Its usually the tray 2 solenoid being sticky. I would remove the solenoid, remove the sticky pad. Then wrap electrical tape where the pad would go. It could also be the pickup...
  10. Re: HP Laserjet Pro 500 Color MFP (M570dn) image problem

    Check the transfer roller in the back. Check to see if there are any cracks. Ive seen this on some Ricoh machines, the transfer roller will have a crack and arc and loose charge.
  11. Replies
    4
    Views
    434

    [Error Code] Re: Mp3555 scan to folder error

    Check the SMBv2v3 firmware. Also are they using Windows 10?
  12. Replies
    1
    Views
    2,059

    [Misc] Re: SCX-6555nx - System Recovery

    ftp://ftp.hp.com/pub/softlib/software13/printers/SS/SCX-6555NX/

    Download the RecoveryFW. Put the "rootfs.tar.gz." file on a thumb drive. Then insert the thumb drive in the usb slot above the...
  13. Replies
    5
    Views
    2,107

    Re: SCX-6545n problem printing and copying

    It wont be the slit glass. If it was you would be getting black lines. I think it may be the transfer roller. Check to see if the transfer roller is cracked or has rips.
  14. Replies
    12
    Views
    2,737

    [Misc] Re: MP 305spf squeaking in the fuser.

    I would but unfortunately there is only one machine inectge office.
  15. Replies
    12
    Views
    2,737

    [Misc] Re: MP 305spf squeaking in the fuser.

    Yup I'm sure.
  16. Replies
    12
    Views
    2,737

    [Misc] MP 305spf squeaking in the fuser.

    I have a MP 305 that is squeaking in the fuser. I have replaced the fuser twice within 2k copies, and its squeaking again. has anyone have this issue? Is there anything way to fix it without...
  17. Replies
    4
    Views
    2,889

    FTP site for Samsung and HP printers

    ftp://ftp.hp.com/pub/softlib/software13/printers/SS/
  18. Replies
    6
    Views
    834

    Re: MP7503 Jam Code 125 and SC720-42

    I would check the wire harness for any wires that are nicked. I had one machine that would do the staple job, and then throw an SC code. I replaced everything the manual suggested. It ended up being...
  19. Replies
    1
    Views
    2,075

    [Misc] Samsung SL-2620DW stuck on Samsung logo

    I have a SL-2620DW that is stuck with the Samsung logo on the screen and wont go passed it. We can print, but thats about it. Would a firmware update fix this? Thanks in advance.

    44701
Results 1 to 19 of 19