Search:

Type: Posts; User: adriansto

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Thread: 045-315

    by adriansto
    Replies
    1
    Views
    87

    [Error Code] Re: 045-315

    Check, reseat, replace the flat cable from MCU pwb to Y M ROS
    Check, replace Y M Ros unit.
    Or replace bad MCU pwb.
  2. Replies
    2
    Views
    89

    Re: V180 - 42-384

    Check AC PSU (PL18.5 item #2).
  3. Replies
    4
    Views
    202

    Re: Error code 116-388 on a c560

    It was detected that no HD is installed, although this is a configuration (there is a FAX) that requires an HD.
  4. Replies
    2
    Views
    186

    Re: Xerox c560 error code 041-355

    IOT Driver PWB Fuse F10 blown.
  5. Replies
    1
    Views
    90

    Re: YWC-1 scanner and HFT Controller

    I have some AccXes service cds.
    Send me mail stoadis@gmail.com
  6. Replies
    14
    Views
    1,326

    Re: Xerox 7545 Fiery stuck at BOOTING KERNEL

    What about to read Fiery install and configuration guide ?
  7. Replies
    14
    Views
    1,326

    Re: Xerox 7545 Fiery stuck at BOOTING KERNEL

    Same date, same time on both copier and Fiery
  8. Replies
    8
    Views
    1,266

    Re: Versalink c405 admin password

    Send me mail stoadis@gmail.com
  9. Replies
    1
    Views
    249

    [Error Code] Re: xerox versant 180 error 099-351

    Problems in the fuser area.
    Sent you some information.
  10. Replies
    8
    Views
    383

    Re: Xerox stuck at startup sheet

    On machine configuration report you can see the machine software version.
    Fiery is bustled or standalone ?
    What number show the 700-006 nvm location ?
    Ask your xerox tech for all of these.
    I have...
  11. Replies
    8
    Views
    383

    Re: Xerox stuck at startup sheet

    What version of software is now in the printer ?
  12. Replies
    1
    Views
    119

    Re: Xerox 560 after a storm error 124-315

    Need to do serial number syncronization procedure.
  13. Replies
    1
    Views
    166

    [Error Code] Re: docucolor 5000ap Service manual

    Only edoc format.
  14. Replies
    2
    Views
    295

    Re: DC252 NVM Setting Value List.

    Diagnostic software works without pws computer.
  15. Replies
    10
    Views
    1,153

    [Error Code] Re: xerox versant 80 error 099-339

    stoadis@gmail.com
  16. Replies
    10
    Views
    1,153

    [Error Code] Re: xerox versant 80 error 099-339

    There are more.
    Pdf service manual 705P01362 & edoc 705P01379
  17. Replies
    10
    Views
    1,153

    [Error Code] Re: xerox versant 80 error 099-339

    There are a lot of possible causes for this error ( gears, sensors, etc ) but noting to do with fuser nip adjustments.
    You need service manual and follow the proper procedure from there.
  18. Replies
    5
    Views
    334

    Re: Xerox C570 - Error 093-317

    Remove black developer housing and inspect the gears.
  19. Replies
    8
    Views
    1,266

    Re: Versalink c405 admin password

    The reset code get back the default admin password, not reset machine to factory default.
  20. Replies
    1
    Views
    206

    [Misc] Re: Feed rollers part number.

    Feed Roll Kit (B98, B4E, RBV) = 604K81850

    Feed Roll Kit (YAO, XY9, MFA) = 604K81860
  21. Replies
    1
    Views
    276

    Re: Xerox C70 Service Manual

    Only in edoc format.
    You need pws for use the manual.
  22. Replies
    21
    Views
    1,511

    [Dead] Re: Colorqube 9301 Error 94-534

    This error is from SBC CPU fan
  23. Replies
    21
    Views
    1,511

    [Dead] Re: Colorqube 9301 Error 94-534

    Drum drive motor, drum driver pwb, defective rear bearing - PL94.20 item 3 = 020K20552
    Before replace pulley check T30 screw holding pulley to the drum.
  24. Re: Replace Xerox 700 IOT PWB BOARD, 960k28862 with XEROX J75 PWBA IOTD, 960k68231

    My opinion is to purchase service manual and follow the proper procedures from there if you want to selfservice the machine.
    From history errors seems the iotd is defect but also there are anoters...
  25. Re: Replace Xerox 700 IOT PWB BOARD, 960k28862 with XEROX J75 PWBA IOTD, 960k68231

    Even the iot driver pwb from C75 looks the same as 700 may be it is not.
    The RAP from edoc say to replace iot driver pwb after you already have replaced the iot exit motor.
    Part number for IOTD=...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4