Search:

Type: Posts; User: miller01123@gmail.com

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    1,695

    Re: Sharp mx 6071 h5-01

    Had the same problem on 3 B&W fusers M3050, H5-01 with no other jams. I replaced POD1 sensor and haven't heard from any of them since.
  2. Replies
    10
    Views
    1,316

    Re: Brother MFC L5900DW Light Copy

    Get a darker blue pencil. Most copiers have a hard time seeing light blue pencil, IME.Especially a cheap one.
  3. Replies
    6
    Views
    670

    [Jamming] Re: MXFN27N jam

    I've found that the center pusher on the assist unit locks up on the guide shaft and causes the unit to go out of timing. This starts to happen after 40 to 50 thousand copies. The only solution is to...
  4. Replies
    2
    Views
    442

    Re: MX-3610 VS MX-3640 fuser

    no way to tell without taking the covers off. the 360fu1 has white wires going to the main connector and the 361fu1 has black wires.
  5. Re: Toshiba version of MX-M1205 not printing

    I have no idea but every time I have a strange problem with a sharp I replace the SD card if it has one. 9 times out of 10 that fixes it.
  6. Re: Toshiba version of MX-M1205 not printing

    Did you try an SD card?
  7. Replies
    13
    Views
    1,979

    Re: MX-3050N showing H2-01 error

    Did you reset the code in sims after?
  8. Replies
    6
    Views
    583

    Re: Sharp MX2651 chirping noise

    Clean and powder (friction reducing powder) the transfer belt cleaning unit side seals. They will make a dog whistle noise if they have toner build up on them. Also the exit unit above the fuser will...
  9. Re: 5050 and 5070 Cyan DV being depleated.

    There is a problem with some machines where the seal under the cleaning blade is not attached properly, causing dusting of the charge. this will pull DV.
  10. Replies
    13
    Views
    1,103

    Re: Sharp MX-5001N firmware needed.

    Also, if it does have a security kit it will say FR11 or FR11U on the ROM on the MFP. You will need the firmware for the security kit. You may have to do an Emergency Update if you can't get into the...
  11. Replies
    13
    Views
    1,103

    Re: Sharp MX-5001N firmware needed.

    I use dban and use the single pass erase. I believe you need at least a 320 gig hdd
  12. Replies
    13
    Views
    1,103

    Re: Sharp MX-5001N firmware needed.

    Was it a blank hard drive? If not, you need write 0s to it.
  13. Re: MX-3110N Faded Prints, Copies Good

    It's a USER password PHIL. Easily found in an internet search. No security breach there. Also changeable by the end user to make the MFP more secure, if so desired by the end user.
  14. Re: MX-3110N Faded Prints, Copies Good

    On the op-panel of the machine you should see a Settings button. That should get you started. The password should be "admin".
  15. Re: MX-3110N Faded Prints, Copies Good

    Thank's PHIL! Should have said Printer Settings instead of Copy Function Settings. Edited my previous post.
  16. Re: MX-3110N Faded Prints, Copies Good

    You could try doing Auto Color Calibration under Settings- System Settings/Printer Settings/Color Adjust or you could try Restore Factory Defaults under System Settings/Storing/Calling of System...
  17. Re: Sharp MX-M7050N Lower fuser web winding

    Yes, there are pressure screws. I've had this exact problem because someone didn't realize that they were there.
    4700847009
  18. Replies
    4
    Views
    831

    Re: MX-6070 with F2-64

    Check the coupler that turns the toner cartridge. I had one that somehow got pushed back and was not touching the cartridge.
  19. Replies
    10
    Views
    1,070

    Re: Sharp MX4100 MX4101

    Try the clutches on the main drive that lift the T1 rollers.
  20. Re: Sharp MX-M7050N Lower fuser web winding

    Did you check to make sure the fuser pressure screws are backed out completely?
  21. Re: Sharp MX-M7050N Lower fuser web winding

    Do you have the right model number?
  22. Re: MX-3640N throwing an occational E7-93

    I always suspect the SD card first.
  23. Replies
    4
    Views
    1,071

    Re: Service mode back door

    You will have to figure out why the home key is not working.
  24. Replies
    5
    Views
    1,477

    Re: MX-5070v high pitch noise

    Clean and powder the felt side seals on the primary transfer belt cleaning unit.
Results 1 to 24 of 26
Page 1 of 2 1 2