Search:

Type: Posts; User: JPazy

Page 1 of 2 1 2

Search: Search took 0.08 seconds.

  1. Replies
    4
    Views
    278

    Re: Service mode back door

    Thank you for the information. The web browser and TigerVNC Viewer worked great to allow access to service mode while waiting for the new Home Key to arrive.
  2. Replies
    4
    Views
    278

    Service mode back door

    Does anyone know a way to enter service mode on Sharp MX 4140 when the Home key isn't responding?
  3. [Misc] Re: Kyocera users forget pin then can't delete job from private print queue

    maybe newer versions of netviewer or through the command center will allow them to be deleted. older machines may require a HDD format to delete those jobs. Back up HDD with U917 to save yourself...
  4. Replies
    9
    Views
    255

    Re: FS-6530mfp out of memory

    have you tried turning off "RAM Disk" under the system menu? It reserve blocks of memory for features such as Private Print and Job Box. Remember to turn it off on the Print Driver as well.
  5. Replies
    9
    Views
    1,035

    Re: Deep Black on Site, FS3920

    i would check the heat roller to see if teflon is worn, looks like streaks get worse at the tail end of the prints. TS tip on stopping the print half way through should indicate if it's drum or fuser...
  6. Replies
    1
    Views
    177

    Re: a4 bizhub iseries

    we use alot of generic cabinets for various A4 machines. Visit this site to see if there's anything you like. Quick Quality Cabinets
  7. [CQ] Re: Kyocera 2500ci copy color not complete and not able to performed toner corve

    Has the optics and underside of platen glass been cleaned? hazy optics may cause an error when running the toner curve.
  8. Thread: taskalfa 300i

    by JPazy
    Replies
    4
    Views
    311

    [Error Code] Re: taskalfa 300i

    i don't think older machines have many F codes explained in the manual. Sounds familiar to a code i had once on a KM-3060 in which the ADF cable had gotten damaged and had to be replaced. You may...
  9. Replies
    3
    Views
    227

    Re: CopyStar Cs2552ci /7100 Finisher

    yes part number is 303JY44011, it's the same staple unit as a DF-770 Finisher from the 00/01 series. We have replaced a couple of defective units. It's been awhile, i don't think it was too difficult...
  10. [CQ] Re: Kyocera Taskalfa 2552ci - Yellow color is missing on status page

    I don't remember if the 2552ci has the little white button to push in on the DV unit which moves the mag roller to the drum, there may be a spring that allows it to move to the drum. Common problem...
  11. Replies
    5
    Views
    444

    Re: 5551ci - Error Occurred at Cassette

    i've seen this a lot on the 500ci series where the lift motor needs replacement. be careful when taking the machine out of auto paper size mode, if they have a fax board installed it will have...
  12. Replies
    4
    Views
    317

    Re: 3501I Stuck on welcome screen

    i have seen this happen sometimes when it's something as simple as a paper jam in the machine when powered on, sometimes it will take forever for the J0000 to trigger. You may want to try opening the...
  13. Re: Taskalfa 307ci ...... Cannot Log into command centre

    i had this happen to me on a Taskalfa 4501i. For some reason the customers IT tech turned off HTTPS and HTTP, which are located under the 'system/network,' 'network settings', 'protocol settings'....
  14. Replies
    2
    Views
    239

    Re: 5052ci Fax Reception problems code U01194

    yes, i reinitialized the fax to factory and even tried a new fax board System 12 out of the box, after it failed i updated firmware. When i spoke to a rep from the sender, they told me their xmit...
  15. Replies
    2
    Views
    239

    5052ci Fax Reception problems code U01194

    maybe someone can offer some advice. Recently installed a Taskalfa 5052ci to replace a Taskalfa 4551ci. Customer indicates since new machine has been installed they don't receive faxes from Answering...
  16. Replies
    3
    Views
    270

    Re: Kyocera P3055 Shifting Alignment Tray 2

    Like Phil said, might be something with the media, maybe try printing the labels from MFP Tray? There is an adjustment for registration (lead and side), but it is prescribe commands sent through IC...
  17. Replies
    5
    Views
    321

    Re: sleep or power saving modes

    Might want to try changing the Sleep Level from 'energy saver' to 'quick recovery', we had success with a customer with the same problem, but they were using Paper Cut.
  18. Re: KFS Connectivity, Power Saver Settings/Power Cycling

    ooops, sorry, i misunderstood, thought you only had a problem with only one machine.
  19. Re: KFS Connectivity, Power Saver Settings/Power Cycling

    If you have KFS you should be able to restart the machine remotely, if you want it restarted during off peak hours, you may want to schedule a firmware update, maybe Sunday morning at 2:00 am. After...
  20. Replies
    1
    Views
    243

    Re: Panasonic DP C213 Transfer Belt

    It's been awhile, but if my memory is correct, the machine will allow one xfer belt reset, after the second reset, the machine will shut down, there is another counter in F8 to reset the Xfer unit...
  21. Replies
    7
    Views
    647

    [Jamming] Re: MX-3570V Duplex misfeeds

    Yes, it does have the Right Tray unit, which I haven't experienced any misfeeds when the paper outputs to that tray. I did remove it and installed the original blank guides, but misfeeding during...
  22. Re: Taskalfa 5551ci service mode entering code changed

    You may want to try running Data Sanitation under System/Network - Data Security. It takes six hours or so, it usually defaults everything but counters back to factory settings. Not sure if it'll...
  23. Replies
    7
    Views
    647

    [Jamming] Re: MX-3570V Duplex misfeeds

    Thank you, yes double checked firmware is up to date and reflashed it to be certain. Checked ribbon cables, and reseated them. Don't see any damage on the cables.
  24. Replies
    7
    Views
    647

    [Jamming] MX-3570V Duplex misfeeds

    I have a Sharp MX-3570V which misfeeds intermittently when duplexing jam code APPD2_S.When it jams it accordians between MFP duplex guide and Right door duplex guide past the second Duplex drive...
  25. Replies
    5
    Views
    575

    Re: Kyocera 300i how to install scanner

    Typically Scanning on a 300i is set up using SMB scan. Kyocera has a TWAIN driver for scanning as well on their site.
Results 1 to 25 of 27
Page 1 of 2 1 2