Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    1
    Views
    172

    Re: Toshiba oblique printing

    There are a couple of different reasons why you might get paper skew:

    1) You may have a corner of paper folded over somewhere in the stack of paper, causing it to be higher at the front or back....
  2. Re: 3551ci - a print error has occurred, add paper to tray 1

    This is the broken feature on the rear guide:

    50912 =^..^=
  3. Replies
    8
    Views
    491

    Re: C454e print rubbish

    It's most likely a PostScript error. Somebody is sending print data in a language that the printer cannot identify, so it prints out the commands exactly the way they came in.

    Given the choice, I...
  4. Re: 3551ci - a print error has occurred, add paper to tray 1

    I know we've already covered this ... but are you SURE that the paper size is not hard-set at LTR? It should be on Auto(Inch).

    That's the only reason I know that the paper size would not...
  5. Replies
    22
    Views
    1,331

    [Jamming] Re: Konica Minolta c6100 Jam??

    I think that I'd put my meter on the motor leads and check to see that you're getting 24vdc (I think it's 24vdc?). If you have voltage then yes, the motor is bad. If you don't have voltage it could...
  6. Re: Good Christmas Present For Copier Techs?

    Here are a couple of not-too-expensive tools, that very few techs have:

    Amazon.com: NEIKO 01970A E-Clip Remover & Installer Tool Set | 4 Piece | SAE | 1/4" to 3/8" : Industrial & Scientific
    ...
  7. Re: 3551ci - a print error has occurred, add paper to tray 1

    Very precise analysis.

    I've replaced 15 or 20 0f those rear cassette guides, usually schools. You'll get an enduser that decides they'll bowling for a strike, with a full ream of paper. The impact...
  8. Re: 3551ci - a print error has occurred, add paper to tray 1

    With the paperclip, if you load STMT-R paper it will still detect as LTR.
  9. Replies
    19
    Views
    530

    Re: Let's talk TURKEY

    My responsibility starts when birdy flies out of the oven, so I won't be able to help on the recipe. Since Mrs. blackcat prefers her turkey white meat hot out of the oven, I get the greatest part of...
  10. Re: Looking for some clarification on Function levels on Bizhub Firmware levels.

    On the 4e series, a firmware change from function level 6 to function level 7 meant no more printing. That's when I learned about SW 25. =^..^=
  11. Replies
    1
    Views
    185

    Re: P2235dw Network Reset

    Don't you love IT guys! They won't be satisfied until the machine is entirely unusable ... completely secure.

    Good to know, thanks! =^..^=
  12. Re: 3551ci - a print error has occurred, add paper to tray 1

    So do your trays display the correct size?

    It's common for a small plastic tab on the rear cassette guide to break. When that happens, the left side of the guide raises up, and incorrectly...
  13. Replies
    6
    Views
    346

    Re: KM5050 SSL e-mail problem

    That's the problem. It won't do it. =^..^=
  14. Thread: NG codes

    by blackcat4866
    Replies
    4
    Views
    331

    Re: NG codes

    I don't suppose that you know what kind of machine that you're working on? =^..^=
  15. Re: Overlay printing and Kyocera Ecosys M3645idn

    What file format is the letterhead overlay in?

    This should not have anything to do with PreScribe. If your letterhead overlay image is a pdf, or tif, or whatever, create a new letterhead image of...
  16. Replies
    2
    Views
    193

    [Misc] Re: HP M608 will not fuse toner

    Is pressure being applied to the fuser rollers? Any special media? What media settings are you currently using? =^..^=
  17. Replies
    10
    Views
    437

    Re: MFC-L861, skewing images...

    I gathered what I did from the Brother online users manual. You could too. =^..^=
  18. Replies
    3
    Views
    314

    Re: c654 low count xbelt skidmark

    Is this machine running any special media, like NCR? That will cause a wide variety of cleaning issues. =^..^=
  19. Replies
    22
    Views
    1,331

    [Jamming] Re: Konica Minolta c6100 Jam??

    I suppose so. Or the sensor may not be functioning. You can test the sensor and motor, yes? =^..^=
  20. Replies
    10
    Views
    437

    Re: MFC-L861, skewing images...

    Two gray levers, opposite sides of the fuser. =^..^=
  21. Replies
    15
    Views
    996

    Re: C3350 swapping IU's ???

    Correct. I have had no success swapping used IU's, regardless of usage. =^.^=
  22. Replies
    10
    Views
    437

    Re: MFC-L861, skewing images...

    No, only one green lock lever, down locked, up unlocked.
    Also check that both the envelope pressure levers are set to the upper position (plain paper). =^..^=
  23. Replies
    10
    Views
    437

    Re: MFC-L861, skewing images...

    If it is the Brother MFC L8610CDW, did you check to see that the imaging drawer is latched in on both sides? =^..^=
  24. Replies
    10
    Views
    437

    Re: MFC-L861, skewing images...

    Could this be a Brother MFC L8610CDW, maybe?

    I don't seem to be finding references to the model you indicate. =^..^=
  25. Re: TASKalfa 7551ci colors go light after a few hundred copies

    ... and those samples? =^..^=
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4