Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 1.14 seconds.

  1. Replies
    31
    Views
    922

    Re: C280 J-3003

    Yes. I can think of no exceptions in 30+ years.

    I have attempted to save partially seizing bearings in the past with generally poor results. Especially in the fuser, you cannot use oil. It will...
  2. Replies
    31
    Views
    922

    Re: C280 J-3003

    I think that's the most important thing about these forums. Most of the truly important things we learn are never documented in any manual or bulletin. Quite often the solutions are discovered...
  3. [Misc] Re: XM 7155 Control panel printing on it's own and then Non responsive...

    We've seen bad Lexmark touchscreens, but it's usually a display issue: they usually roll and flicker like a poorly tuned vacuum tube TV.

    It sounds to me like you have a touchpad issue ... replace...
  4. Replies
    31
    Views
    922

    Re: C280 J-3003

    It looks as if the leading edge tried to follow the top of the transfer belt, missing the fuser inlet.

    On this jammed image do you notice diminished second transfer on the jammed page?
    I notice a...
  5. Replies
    16
    Views
    498

    Re: 458e shuts down during job

    There are UPS devices that can support a copier, but they are not cheap. A 15A copier requires 1800Watts (P=IV) capacity. The typical computer battery backup is rated at 500Watts. We have...
  6. Re: kyocera mita km2050 dirty toner at the back of paper

    What exactly are you filling the toner cartridge with? =^..^=
  7. Thread: HDD wipes

    by blackcat4866
    Replies
    5
    Views
    208

    [Misc] Re: HDD wipes

    None perceived, thanks. And thanks for the details I could not provide. =^..^=
  8. Re: Frequent problem with Ecosys P2040dn/M2040dn

    The shorter the time the better. On machines at home and in the office I set 5 minutes. It's about what the end-user will accept. =^..^=
  9. Replies
    16
    Views
    498

    Re: 458e shuts down during job

    I've seen this situation. The UPS usuals squeals at you ever time you wake up the machine, and fuser errors. =^..^=
  10. Re: Frequent problem with Ecosys P2040dn/M2040dn

    Yes it does help. The sleep timer is the amount of time until the fuser temperature lowers. Plastic construction fusers tend to fail quickly if kept at high temperature for a long time.

    The few...
  11. Re: Problems Registering used machine with KFS

    Good to know! Thanks. =^..^=
  12. Re: Frequent problem with Ecosys P2040dn/M2040dn

    I don't believe re-engineering the fuser mechanics is one of our options as field technicians. How about focusing on plausible options like reducing the sleep timer? =^..^=
  13. Thread: HDD wipes

    by blackcat4866
    Replies
    5
    Views
    208

    [Misc] Re: HDD wipes

    I used to work on older MFP's ... most Canons hold System Software on the HDD, and wiping the drive would require reloading firmware. It would become a brick until firmware was reloaded. =^..^=
  14. Replies
    4
    Views
    139

    Re: toshiba 281C drum replacement

    Best left in the museum as an example why NOT to build carousel type color MFP's.

    I wonder what would happen if you were to turn the developing units like a rock tumbler the whole time you were...
  15. Replies
    45
    Views
    1,401

    Re: Looking at selling Konica Minolta.

    Did you ever notice that there are just as many awards as there are models of MFP's? It makes one think that it's just another sales device with little actual significance.
  16. Replies
    11
    Views
    462

    Re: Toshiba e4555c IP address issue

    It doesn't have to be a printer, scanner, copier, or MFC to be a duplicate IP. In my experience lately it's been either a wireless laptop or a smartphone. All it's got to do is want the same IP...
  17. Re: Problems Registering used machine with KFS

    You might check to see that the MFP's DNS is set correctly. What I'll usually do is connect my laptop to the network drop and let DHCP assign an address. Then from Command Prompt > ipconfig/all >...
  18. Replies
    7
    Views
    163

    Re: e-STUDIO2500AC Lifetime ?

    About the only way you can run this machine for any length of time, is to start your own K2 graveyard. If you buy 6 or 8 of these corpses cheap, maybe you'll have enough parts to make one of them...
  19. Thread: XM3150

    by blackcat4866
    Replies
    6
    Views
    206

    Re: XM3150

    Did you print the error log? Codes can be recorded that never show on the display. =^..^=
  20. Replies
    45
    Views
    1,401

    Re: Looking at selling Konica Minolta.

    Image quality is very stable. The latest models with charge rollers, drums yield exactly what they say or slightly less.

    Boards and firmware can be quirky, like all KM. =^..^=
  21. [Misc] Re: Problem with e_studio 757 (dot on printed paper)

    I think I'd replace the C6000 developer. The developing unit is probably fine. =^..^=
  22. [Misc] Re: Problem with e_studio 757 (dot on printed paper)

    Take a look at the trough in the bottom of the drum unit. If it's full of toner, the developer is overtoned. =^..^=
  23. Replies
    12
    Views
    424

    [Jamming] Re: C754e jam code 1102

    Jam 11-02 is typically seen when paper isn't picked up. I've seen it happen when the PE flag is broken and the tray runs out of paper. Or when the vertical guide is dislodged.

    But what you really...
  24. Replies
    2
    Views
    156

    Re: Bizhub c552 print problem

    Try these originals:
  25. Replies
    9
    Views
    408

    Re: Question regarding Kyocera MFP'S

    Yeah, there are improvements to the FR-8550H fuser. I hope it fixes the cascade of rust contaminating rotation sensors. The longest I've seen one of these fusers go is 180K. =^..^=
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4