Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    19
    Views
    466

    Re: Biz C224e - Muratec version?

    You can also change the hostname to: KonMin224 or whatever you like.
  2. Re: PIVOT for Effective Parts Management

    Who is using this? =^..^=
  3. Re: Kyocera FS-C8520 transfer belt cleaner problem

    So the cleaner is backed up again. Check the spout and auger system moving the toner through the spout. It's very common to split a gear or two in the spout drive.

    TASKalfa 2551ci parts pipe...
  4. Replies
    8
    Views
    305

    Re: Kyocera P4040dn fuser problem.

    I feel like I should know this, since I worked on quite a lot of the Harriers, but I do not, and Kyocera did not include a repetitive defect chart in the earlier manuals, which includes CS-8030 and...
  5. Replies
    9
    Views
    218

    Re: C-3906 Pro 1100

    Just to confirm, yes the machine will initialize with an open lamp, but may go into long warmup cycles. Also, an intermittent thermostat can give these effects. They're not that expensive, and can...
  6. Replies
    10
    Views
    208

    Re: 2250P deletions

    Were these fed SEF or LEF? I see the ... deletions ... but can't decide if the the drum is accumilating charge because of drum cleaning ... I guess that makes the most sense, with LEF. And the drum...
  7. Re: HP Designjet XL 3600DR PS Service Manual

    More information ... and I know even less than before.

    The roll2 media sensor made no difference, and detects paper present/paper absent in diagnostic mode.
    The roll2 rewinder is now passing the...
  8. Replies
    8
    Views
    171

    Re: HP DJ T795

    I suppose that you could clip onto the ribbon contact at each end of the ribbon cable, set you're meter to tone, then repeatedly slide the carriage through it's entire range of movement .. but you're...
  9. Re: Heads-up: 7353ci CQ light bands OOB or after service

    Thanks! That's a good one. =^..^=
  10. Replies
    4
    Views
    175

    Re: CS3051 color issue

    Copies will never look as perfect as direct prints, due to resolution loss from the scanner, but that's pretty extreme. It sounds obvious, but have you thoroughly cleaned the scanner optics and CCD...
  11. Replies
    16
    Views
    409

    Re: C-364 series, rotating faxes??

    On the next visit this same customer had taped a small note to the tray saying "Do not place originals here!". They taped the note directly on top of the length sensor. :rolleyes:
  12. Replies
    3
    Views
    147

    Re: Kyocera M5526cdw colour print issues

    How do the prints look when printing from the KX driver on your PC? Where are the samples of these terrible prints? =^..^=
  13. Replies
    2
    Views
    152

    Re: Kyocera M4132idn Printer Suspending

    It sounds as though you haven't seen the machine yet.

    If you can get it to reset, even temporarily, I would boot it up off the network, then print off the error log.
    =^..^=
  14. Replies
    10
    Views
    526

    Re: C-3110, not printing...

    Were you successfully connecting directly to your laptop? =^..^=
  15. Re: BIZHUB C224 missing "Store address" tab in the web interface

    The first thing that you'll notice if the HDD is UnSet or failed is the message: "Animation data is not available". Fax and scan functions will also be unavailable. =^.^=
  16. Replies
    19
    Views
    510

    Re: Wide Format Printers 60+"

    The only thing that I can add to this discussion is that I've serviced a Z6200 a few times, and it seems reliable overall. =^..^=
  17. Replies
    8
    Views
    373

    Re: P3060 Jamming

    I've gotten these codes when the side guides were 1mm too tight, causing the paper to bridge up in the middle. Same with the endstop. =^..^=
  18. Replies
    9
    Views
    218

    Re: C-3906 Pro 1100

    The C3903 did clear, then re-occurred after a paper jam (customer had to open/close the imaging drawer). For a couple weeks it was every other day. =^..^=
  19. Replies
    9
    Views
    218

    Re: C-3906 Pro 1100

    The only time I've seen the C3906 is when my enduser sprayed an entire can of air into the fuser, thoroughly freezing the thermistor. I'm surprised that there weren't shattered pieces of heat lamp...
  20. Replies
    16
    Views
    409

    Re: C-364 series, rotating faxes??

    Make sure that the document feeder original tray is not detecting Letter LEF originals as Ledger SEF originals. Malfunctions of the original length sensor will cause the machine to reduce the images...
  21. Replies
    5
    Views
    246

    [Jamming] Re: Toshiba e studio 457(two)

    It looks like the whole Loire series uses C0-17839000 for the reverse sensor S10.
    It's a type BL sensor:

    49738

    =^..^=
  22. Replies
    5
    Views
    246

    [Jamming] Re: Toshiba e studio 457(two)

    This is the reverse sensor, hanging slack:

    49737
  23. Replies
    4
    Views
    143

    Re: installation bizhub c3350

    You're doing a new installation on 7 year old copier? =^..^=
  24. [Wanted] Re: Kyocera KM-2035 (or KM-1635) Printer Board/Card

    If you do find one, it will cost more than your used 10 year out digital copier. =^..^=
  25. Replies
    13
    Views
    1,014

    Re: IP Address no Op Panel

    For things like jams & Add Toner indications you can browse the web interface for more information. Anything more complex ... might be impossible to diagnose.

    Slightly off-topic: I had a customer...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4