Search:

Type: Posts; User: mrfuser

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    2
    Views
    156

    Bizhub c3350 scan settings anyone?

    I have a client with a couple of okder c3350 units that they are needing it to scan default black and white and for the life of us we canít see a way to do that. Most bizhubs you can change the...
  2. Replies
    12
    Views
    239

    Re: Mpc4502a With single pass feeder sc700-00

    Yes sir I tried every combination
    I even slid the paper in and let it lift the tray and pulled her back out about 20 times
  3. Replies
    0
    Views
    53

    Mk-738 fax kit for bizhub c3350

    Anyone have a spare mk-738 mounting kit for the fk-512 on the c3350 they want to sell?
  4. Replies
    12
    Views
    239

    Re: Mpc4502a With single pass feeder sc700-00

    I went back today and ran over 900 pages through the feeder without a single problem so I guess whatever was in there worked its way out
  5. Replies
    12
    Views
    239

    Re: Mpc4502a With single pass feeder sc700-00

    Sorry, typo it is 700-01. I went through and cleaned everything and am going back again today and will check again. I personally ran a couple of hundred pages and it worked perfect and as I said...
  6. Replies
    12
    Views
    239

    Mpc4502a With single pass feeder sc700-00

    Client got a small sticky stuck in the machine and they removed it before I got there. Unfortunatley it then started to go into an sc700-00 condition randomly. I went through the feeder and did not...
  7. Thread: Mpc3001 sc531

    by mrfuser
    Replies
    13
    Views
    301

    Re: Mpc3001 sc531

    I replace the two fans on the left side the front fan comes on no problem but the real one will not come on and I tested the rear one on the front and it comes on just fine

    any other ideas on this...
  8. Thread: Mpc3001 sc531

    by mrfuser
    Replies
    13
    Views
    301

    Re: Mpc3001 sc531

    Ok. Swapped left side fans. Only rear one was not coming on and even after swapped it wonít come on. Tested in front slot and it works fine there. Followed wires back and all seemed good even...
  9. Thread: Mpc3001 sc531

    by mrfuser
    Replies
    13
    Views
    301

    Re: Mpc3001 sc531

    Thank you very kindly!
  10. Thread: Mpc3001 sc531

    by mrfuser
    Replies
    13
    Views
    301

    Re: Mpc3001 sc531

    sc351 or 531? Wi was referring to 531
  11. Thread: Mpc3001 sc531

    by mrfuser
    Replies
    13
    Views
    301

    Re: Mpc3001 sc531

    I’m sorry to have offended you gentlemen that was not my intention. I was figuring because I had two different questions that I should open to different threads but if the consensus is not to do...
  12. Thread: Mpc3001 sc531

    by mrfuser
    Replies
    13
    Views
    301

    Mpc3001 sc531

    Ok got the sc531. Changed both fans by the fuser. It will run a single page no problem, but as soon as we try 3 duplexed pages we get another sc531. Any ideas?
  13. Replies
    2
    Views
    105

    Mp c3001 exhaust fan part

    Anyone have the part number for the exhaust fans by the fuser on the C3001?
  14. Replies
    13
    Views
    272

    Re: Sp c430dn black toner bottle not rotating

    Ok so the pump rotates the toner bottle on this unit? Is this a big job? Client needs to know cost vs replacement of machine
  15. Replies
    13
    Views
    272

    Re: Sp c430dn black toner bottle not rotating

    Not asking for toner but when I cheat the door and do a manual add toner you can obviously see the block bottle struggle to turn
  16. Replies
    13
    Views
    272

    Sp c430dn black toner bottle not rotating

    Looks like the black toner bottle is not being rotated by motor. Other three seem to turn just fine. Although all colors are washed out. Is this a huge job does anyone know?
  17. Replies
    14
    Views
    860

    Re: C284e washes out colors

    Ok replaced yellow drums dndv and yellow is super high now and other colors are still washed out and levels show very low. I swapped out the sub hopper assembly and the small gears that mesh at the...
  18. Replies
    32
    Views
    5,604

    Re: C364 32-01 exit jam

    in my 30 years I have never seen any machine duplex card stock reliably

    QUOTE=John Kaufmann;1489097]Thanks for getting back on that question. I have a machine that's still not reliably duplexing...
  19. Replies
    14
    Views
    860

    Re: C284e washes out colors

    Yes oem drum and dv assembly and yes cleaned print head. Get Atc errors for rear sensor and yellow
  20. Replies
    14
    Views
    860

    Re: C284e washes out colors

    Doesnít seem to be. All the colors are now very washed out
  21. Replies
    14
    Views
    860

    C284e washes out colors

    We have a client with a c284e that was losing yellow so we replaced yellow drum and developer and that seemed to work for a while then it came back. We also replaced the itb assembly, cleaned...
  22. Replies
    32
    Views
    5,604

    Re: C364 32-01 exit jam

    I replaced the entire assembly from a donor machine and it has worked fine ever since. I didnít have time to try each individual part, sorry.
  23. Replies
    11
    Views
    865

    Re: C3350 vs c3351 fuser?

    does it work without error?
  24. Replies
    3
    Views
    270

    Re: C284e yellow almost missing

    I went back to replace hopper assembly because it wasnít adding toner. New hopper assembly had purple wires on left plug instead of white and didnít seem to fit exactly even though it came from...
  25. Replies
    3
    Views
    270

    C284e yellow almost missing

    We have a client with a c284e that the yellow is almost missing on, the color is super washed out. We replaced the iu and transfer belt and toner is oem and same result. Sensor reads about 7 , same...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4