Search:

Type: Posts; User: AMS

Page 1 of 2 1 2

Search: Search took 0.05 seconds.

  1. Thread: mp6001

    by AMS
    Replies
    3
    Views
    239

    mp6001

    I have one giving me the service code sc231. F gate error. Manual says replace BCU Or controller boards. Its usually something else causing the issue besides the boards. I have never had this code on...
  2. Thread: mpc2503

    by AMS
    Replies
    8
    Views
    1,767

    Re: mpc2503

    Went there today and got the service log. It was a 670-1. The manual just said mechanical failure. There was also a bulletin on this problem. Several things it could be. Updated firmware today. Wait...
  3. Thread: mpc2503

    by AMS
    Replies
    8
    Views
    1,767

    mpc2503

    I had a customer call up and say the machine had a functional problem. I asked them what the code was and they said there was no code. I had her turn it off and on and it worked again. Then they...
  4. Thread: mpc 307 part

    by AMS
    Replies
    3
    Views
    343

    [Misc] Re: mpc 307 part

    I ended up using a mpc 305 bracket. With a little velcro and wire I got it to hold in real tight. You got to do what you got to do. Thanks
  5. Thread: mpc 307 part

    by AMS
    Replies
    3
    Views
    343

    [Misc] mpc 307 part

    We just got in a MPC 307 from a whole seller. The hard drive was removed from the copier and they also took out the bracket that holds the hard drive. I could not find the bracket in the parts...
  6. Thread: MPC 305

    by AMS
    Replies
    3
    Views
    416

    Re: MPC 305

    Thanks
  7. Thread: MPC 305

    by AMS
    Replies
    3
    Views
    416

    MPC 305

    Does ricoh sell the fuser reset fuse separate for this model? Its a lot smaller connector then the other models. I looked through the parts and could not find it. If they do, do you happen to know...
  8. Thread: MPC2003

    by AMS
    Replies
    9
    Views
    696

    [Error Code] Re: MPC2003

    Thanks to all, it was the one way gear slipping. I had no clue it even used a one way gear in that assembly. Now I do!! Thanks again.
  9. Thread: MPC2003

    by AMS
    Replies
    9
    Views
    696

    [Error Code] Re: MPC2003

    Not this time. I had updated this copiers firmware about 8 month ago for other issues.
  10. Thread: MPC2003

    by AMS
    Replies
    9
    Views
    696

    [Error Code] MPC2003

    I have one popping up an sc569. I replaced the pressure release motor and home sensor. I replaced the fuser. It would never do it while I was there running it. Today I saw it happen. When I was...
  11. Thread: MPC4502

    by AMS
    Replies
    6
    Views
    570

    Re: MPC4502

    Thanks for all the input. Once I looked at the schematic I followed to the connectors. I had an end pin bent down on the IO board causing the issue. I figured it was something I did to cause it. Not...
  12. Thread: MPC4502

    by AMS
    Replies
    6
    Views
    570

    MPC4502

    The original problem was sc554. The fuser belt was shredded off. I replaced the fuser with a new one with the reset fuse in it.Did sp5810-2 The sc554 did not reset. There was a bulletin to follow for...
  13. Thread: MP 3352

    by AMS
    Replies
    3
    Views
    391

    Re: MP 3352

    Figured that was what it would be. The customer thought it was a good idea to used canned air on it. What a mess that made. That was about a month ago. I guess it worked into the feed unit. The toner...
  14. Thread: MP 3352

    by AMS
    Replies
    3
    Views
    391

    MP 3352

    I have one of these machines that is bending under the lead edge of the copy right at the vertical rollers. Its like the rollers are not turning and the feed clutch is pushing the paper up to fast....
  15. Thread: MP4054

    by AMS
    Replies
    9
    Views
    953

    Re: MP4054

    yep that's what I had to do is replace nv ram. Thanks for all the input.
  16. Thread: MP4054

    by AMS
    Replies
    9
    Views
    953

    Re: MP4054

    yes I can get the reports. There has been no service codes except for the disconnected finisher. I can do everything in the factory mode just wish I knew why I cant get in using the regular service...
  17. Replies
    12
    Views
    972

    Re: MPC 3002 swapping out all boards

    the controller board and bcu serial numbers have to match. Different hard drives will give you address error so you will have to format it. You can change serial number in the factory mode.
  18. Thread: MP4054

    by AMS
    Replies
    9
    Views
    953

    Re: MP4054

    The service mode lock was turned off in user tools. I have another 4054 here so I will swap boards around and see if that will help. Just want to know what is causing the issue.
  19. Thread: MP4054

    by AMS
    Replies
    9
    Views
    953

    Re: MP4054

    I believe that service code is sp 5081 but its not in the factory service mode. I could not find anything in the user tools admin part.
  20. Thread: MP4054

    by AMS
    Replies
    9
    Views
    953

    MP4054

    Just got the copier in on a lease return to redo for sale. It has approx 35000 copies on it. The machine will not let me get into the service mode. It will let me get into the factory service mode...
  21. Replies
    20
    Views
    4,261

    Re: PCU rebuild kit for '03 series

    I just talked with the NA trading rep and he said they will be coming out with a new rebuild kit in a month or so. Its in the testing phase right now.
  22. Replies
    3
    Views
    750

    [CQ] Re: mpc 5503 magenta offset

    We bought this copier used from a distributor. I printed out the sp reports and noticed that there was a lot of settings changed from default. All the heat settings were changed and voltage settings...
  23. Replies
    3
    Views
    750

    [CQ] mpc 5503 magenta offset

    I have a machine that only offsets the magenta. If you do the printer color test print out the magenta line and square repeat on the copy. It is light but you can see it. I tried another fuser, whole...
  24. Thread: MPC 5503 Jam in C

    by AMS
    Replies
    5
    Views
    1,096

    Re: MPC 5503 Jam in C

    I finally found the problem and it was an easy fix after all. There is s sensor on the side frame for the transfer separation unit. There is a small black plastic cover covering the wires. Its the...
  25. Thread: MPC 5503 Jam in C

    by AMS
    Replies
    5
    Views
    1,096

    Re: MPC 5503 Jam in C

    I am not explaining my problem clear enough. The jam logging data does not matter where the jam occurred. As long as the paper does not jam in C section of the copier the copier resets. If I run...
Results 1 to 25 of 47
Page 1 of 2 1 2