Search:

Type: Posts; User: ricohrice

Search: Search took 0.12 seconds.

  1. Replies
    7
    Views
    820

    [Jamming] Re: MX-3570V Duplex misfeeds

    I know this sounds wierd... but what is your firmware level? I've found in some rare cases that updating the firmware on these models fixes some duplex jamming issues.
  2. Replies
    11
    Views
    1,562

    Re: New sharp colors/ mx3070 / 3071 etc

    We have eliminated most of our fuser issues with these machines by running the fuser cleaning mode in system settings\image quality adjustment\fuser cleaning mode.
    I run the adjustment at every...
  3. Replies
    12
    Views
    1,796

    [CQ] Re: MX2610 Magenta colour shift

    I don't see this mentioned anywhere, but when I have any color reg problems I run a 44-13 with the calibration jig (UKOG-0318FCZZ), and then a 44-2. After that re-due the full calibration.
  4. Replies
    1
    Views
    338

    Re: mx623 tray 3 non op

    Pull the paper feed unit and check you paper height detection sensor M1LUD, make sure the actuator is is moving and that the sensor is triggering with sim 30-2. You can also track it back to the PCU...
  5. Replies
    5
    Views
    2,898

    [Error Code] Re: mx-fn10 finisher with FGMJ JAMS?????

    Take the paper pass and plate out of the machine and check the jewel sensor, make sure it's there and not sticking anywhere, I've seen them stick to the duplex guide above the paper pass.

    hope...
  6. Replies
    1
    Views
    417

    Ricoh tech available

    I am a factory certified Ricoh and Konica Minolta technician with Sharp experience as well. I have 10 yrs in the industry as well as my A+ and Net+. I am willing to relocate anywhere within the...
  7. Replies
    1
    Views
    807

    Experienced Ricoh Tech in Reno,Nv

    I am an experienced Ricoh tech and I just relocated to the Reno area. I am reliable, well trained, and able to handle whatever comes my way. Please contact me if interested at srice1553@yahoo.com
  8. Replies
    0
    Views
    489

    Ricoh Tech Heading South

    I will be moving to the Tampa/St. Pete/ Sarasota area the week of November 7th. I am currently seeking employment in the region. Please contact me if interested, I am (or at least was recently) a...
  9. Replies
    0
    Views
    640

    Ricoh Tech Relocating to Tampa/St. Pete

    I am a fully certified Ricoh trained technician that will be reloctacting to the Tampa/St. Pete area. I am hoping to establish employment prior to my arrival in October. I am a well versed tech...
  10. Replies
    9
    Views
    1,331

    Service Bulletin #38 Dated 6-2-09 is supposed fix...

    Service Bulletin #38 Dated 6-2-09 is supposed fix this problem. Did you install the new style touch panel?

    http://www.rfg-esource.com/stellent/groups/b2c/documents/bulletins/rfg039352.pdf
  11. Replies
    5
    Views
    2,589

    I am fighting the same issues on multiple MP...

    I am fighting the same issues on multiple MP 9000's. I have done most of the same things, but I have also adjusted the separation pressure and that seems to be making a differance. Remove the feed...
  12. Thread: SAVIN 2055DP

    by ricohrice
    Replies
    2
    Views
    653

    What jam code/codes is the machine logging?

    What jam code/codes is the machine logging?
  13. Thread: MP9000

    by ricohrice
    Replies
    2
    Views
    562

    MP9000

    Does anyone have any ideas regarding the MP9000's that show the set fuser unit when it is already set?
  14. Replies
    2
    Views
    1,510

    you can try to format the address book data, but...

    you can try to format the address book data, but I would have an HDD on hand if its a long drive.
  15. Replies
    20
    Views
    2,984

    What is the pay you are looking to provide?

    What is the pay you are looking to provide?
  16. Replies
    15
    Views
    3,231

    replace all 6 dev bushings

    replace all 6 dev bushings
Results 1 to 16 of 16