Search:

Type: Posts; User: copyman

Page 1 of 20 1 2 3 4

Search: Search took 0.90 seconds; generated 40 minute(s) ago.

  1. Re: KonicaMinolta bizhub-40p Printer, MS-DOS driver

    If all else fails try using the HP 4 driver which is based on standard driver language. We've used this old driver on many old printers & copiers when no driver available. Only thing is you lose all...
  2. Replies
    5
    Views
    140

    Re: Bizhub C253 K toner port blocking

    Are you sure it's exclusive to the black. There is a known issue with the waste system getting blocked up and you are right the machine has to be torn down to get to it. It is such a big job many...
  3. Replies
    8
    Views
    338

    Re: General Questions on C3350

    Not sure if Kon/Min ever made a good all in one small box, color or B&W? Going way back to the PP1390, it was bad. Color was no better after all these years. Actually only AIO good model is the Biz...
  4. Replies
    3
    Views
    110

    Re: Konica Minolta Color Mismatch - Looks 3d?

    Any "P" codes? Usually when reg is off like that you will have "P" codes. Touch small oil can icon at bottom of screen to see.

    My guess is you may need a drum or two or maybe new transfer belt or...
  5. Replies
    8
    Views
    338

    Re: General Questions on C3350

    Same footprint as the C35!

    Light fuse, get away!
  6. Re: Konica c364e no servicer is registered contact your administrator

    Sorry you don't see my point. If you read "most" of my posts you will see my nature is to help people on this forum. But it comes to a point that's all that can be done.

    Just a suggestion, you...
  7. Re: Konica c364e no servicer is registered contact your administrator

    Wait let me get this right you want to save time but it's ok for us to waste our time trying to explain the soft switch procedure. How it usually works is a tech spends hours, trying everything...
  8. Replies
    10
    Views
    388

    Re: Bizhub Fuser Rebuilds

    Couldn't read what copier adDICK said but sure I din't miss anything:confused:

    Good question, I rarely change the bearings, etc depending on the clicks. Most of the time the fuser was no where...
  9. Re: Konica c364e no servicer is registered contact your administrator

    I agree. This is where it ends for me. You have been given some great support here, including the password to get into security mode! You will need a service manual to proceed. Change software...
  10. Replies
    10
    Views
    388

    Re: Bizhub Fuser Rebuilds

    Yes I've rebuilt many 4 series fusers, no 8 series yet. Much easier than the C253 fusers!

    Aftermarket China parts only. Copylite products out of FL sells everything needed to rebuild units, except...
  11. Re: Konica c364e no servicer is registered contact your administrator

    As my original post stated I figured you were talking about authencation mode. Had this same thing a while back and think it was a softswitch had to be changed.

    Check switch # 12 and make all 0's
  12. Replies
    2
    Views
    141

    Re: Bizhub c550 error c4501

    All I can think of is those ribbon cables for laser unit. If they are the same as a few other Kon/Min PH laser units I've changed the ribbon cables were tricky to seat properly. I would look at those...
  13. Re: Konica c364e no servicer is registered contact your administrator

    Think he means it was in defence dept and had authenication cards. You should be able to turn off in admin mode "authenication off" or if not showing because of higer security than you will have to...
  14. [Misc] Re: what chemicals are you using to clean one ways on KM units

    I seem to recall canon machine saying refurbished in Mex or something like that. And think I remember how nice and new they looked but didn't last long.

    Back in the day you could send covers away...
  15. [Misc] Re: what chemicals are you using to clean one ways on KM units

    Haha we are lucky to still be alive! Heck in the 60's we rode our bikes in the fog behind the DDT trucks that drove around the neighborhoods fogging for mosquitoes! Way before EPA was around.
  16. [Misc] Re: what chemicals are you using to clean one ways on KM units

    Good advice but have to disagree about "not" scuffing the shaft. Scuffing up the shaft with "scotch brite" pad only was even recommended to us by Kon/Min factory rep. Like the other poster said make...
  17. [Misc] Re: what chemicals are you using to clean one ways on KM units

    Speaking of chemicals, us old time techs were exposed to so many chemicals 30-40 years ago. A few I remember is Sharp Pikle drum polish to polish Cadium drums which in itself is deadly and also a...
  18. Replies
    30
    Views
    2,356

    Re: Removing politics from this forum

    Myself and many more members here are right behind you. Like I said before unfortunately this forum will become totally a polictical forum with 4 or 5 people replying to 3 or 4 same old hate Trump...
  19. Replies
    8
    Views
    290

    Re: Platt Tool Case Pallets - Opinions?

    I'm with you and still carry the old style "briefcase" toolbag. Most of the techs I know have switched to the soft shoulder style tool bags. They laugh at me when they see I still use old style. But...
  20. [Misc] Re: what chemicals are you using to clean one ways on KM units

    We just use alcohol to clean oneways and scuff up the shaft with a scotch brite pad. lately I've just been replacing them when I replace the rollers but many of my fellow techs just clean them.
    ...
  21. Replies
    8
    Views
    284

    Re: Replacing the 4 series MFPB and PRCB

    I believe the total counters & serial numbers are kept several different places on K/M copiers, MFB, SSD,Control panel pwb and maybe one more place. Think Blackcat posted this as well.

    Like I...
  22. Replies
    8
    Views
    284

    Re: Replacing the 4 series MFPB and PRCB

    Of course they want to sell you a new board. You can swap one board at a time for troubleshooting purposes and I have also swap the MFP board and left in machine but always used the SSD from the...
  23. Replies
    12
    Views
    844

    Re: One of the first Sharp fax brochures?

    Ouch! Showing our age! LOL
  24. Thread: C300i

    by copyman
    Replies
    10
    Views
    453

    [Error Code] Re: C300i

    [QUOTE=EarthKmTech;1400088]Number 1

    with the 0002 error - i have seen this when assemblers pushed the optional tray(s)/LCT multi pin connector in on an angle and bent one of the pins in the...
  25. Replies
    12
    Views
    844

    Re: One of the first Sharp fax brochures?

    Was selerex a parts company or am I thinking of sel-drum?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4