Search:

Type: Posts; User: copyman

Page 1 of 20 1 2 3 4

Search: Search took 0.61 seconds.

  1. Replies
    6
    Views
    201

    Re: Bizhub C203 - Warming Up

    Agree with allan, you need an image unit with new chip to reset and setup the developer. Go on ebay and get a NEW GENUINE magenta IU and be done with it! I've seen them for $100. Unless of course you...
  2. Replies
    18
    Views
    8,911

    Re: reset tool, A145FW.tar

    Make a small donation and someone will send you the firmware.
  3. Replies
    6
    Views
    201

    Re: Bizhub C203 - Warming Up

    Need more info. Help us to help you! You can never provide enough info & details on a tech forum. You get as much help back as info you provide. It's hard enough to troubleshoot over the internet.
    ...
  4. Replies
    10
    Views
    505

    Re: The Worst Paper I Have Ever Seen

    Come on guys, the days of blaming paper is long past. Use to blame paper for everything, ha-ha.

    I just don't see many issues with paper like the old days. Perhaps excessive paper dust and some...
  5. Replies
    23
    Views
    1,836

    Re: Konica Minolta vs. Toshiba

    Thanks slim, figured it was something like that. He's like every other dem I know, they are in panic mode with Sanders likely nominee. Socialist vs Trump = 4 mores years of Trump = at least one more...
  6. Replies
    23
    Views
    1,836

    Re: Konica Minolta vs. Toshiba

    No sure what salesguy could of posted that many times in a row because have him blocked. Hopefully he hit the submit button by mistake and not going on a tirade with dem rhetoric.

    Anyway I wanted...
  7. Thread: 2550B

    by copyman
    Replies
    14
    Views
    557

    Re: 2550B

    Thanks everyone for the replies!

    I used the 1027 OEM units.

    Going there tomorrow and will try the suggestions. Will report back with what I found.

    Thanks again
  8. Replies
    23
    Views
    1,836

    Re: Konica Minolta vs. Toshiba

    Konica Minolta: user friendly, tech friendly, inexpensive to run, and way too many good things to list!

    Toshiba: Light fuse get away !!!!
  9. Re: Can I put a used SSD board from one machine into another?

    I've swapped just the ssd several times and only once it didn't work mostly C224's. It says in serv man never to swap more than item. Believe the 3rd place info is kept is the control panel. So...
  10. Re: Can I put a used SSD board from one machine into another?

    Yes you can use ssd from another machine. As long as you only swap one thing at a time like the MFP, SSD, etc

    Think there is also a SSD reset firmware that might be an option. It resets SSD then...
  11. Thread: 2550B

    by copyman
    Replies
    14
    Views
    557

    2550B

    Don't know Ricoh that well. Would normally turn ricohs over to a friend but will be upgrading later this year when budget money comes in (so they say, you know old saying "buyers are liars")

    What...
  12. Replies
    14
    Views
    617

    Re: Problem with Bizhub C224

    It's not the paper. Seen this same thing many times and my prior posts explains how to fix. If you put a new developer unit in and still have a bad drum it will dump the new developer! ANY color bad...
  13. Replies
    14
    Views
    617

    Re: Problem with Bizhub C224

    And as most know you can use K drums in place of color with chip change. Use all genuine K drums. And if you look around on this forum you may find where I posted procedure to turn black DV unit to...
  14. Replies
    14
    Views
    617

    Re: Problem with Bizhub C224

    The black developer dumped. Most likely from overlife or crap aftermarket toners or drums! You can try and recover the black developer unit but not easy. Personally I would put a "New Genuine" K drum...
  15. Thread: light image

    by copyman
    Replies
    8
    Views
    747

    Re: light image

    [QUOTE=Gab;1282448]i replaced a heat roller at a biz 350 and opc , blade, developer and spacers (all genuin) at a biz 223. At the beginning everything was ok . After two weeks at the same time both...
  16. Replies
    8
    Views
    404

    Re: Bizhub 554e fax problem

    Change "fax marketing area" in service mode to your area. There are 2 marketing area settings, 1 for the machine and 1 for fax.
  17. Replies
    2
    Views
    396

    [Misc] Re: Konica Minolta Broken PCB Connector Fix

    Nice job! Thanks for the detailed instructions. Hopefully I never have to use them:rolleyes:. At this point in business with time being so valuable think I would just go buy another finisher from...
  18. [Error Code] Re: Bizhub 454e detects high toner density by TCR sensor - Error code C2558

    I gave you my opinion after working on 100's of this model. And have the same issue you describe at least 50 times. So dude you do what you want and gurantee it will cost you more in the long run....
  19. [Error Code] Re: Bizhub 454e detects high toner density by TCR sensor - Error code C2558

    Disagree this machine should be used for a door stop. This is a great model that runs without any service calls. As the other poster said replace "any" other consumable over life, transfers belt etc....
  20. Replies
    10
    Views
    381

    Re: logical format problem - bizhub c454e

    I have seen that before. Think I googled it and found the solution to get rid of message. If I remember correctly the google search brought me back to this forum where the procedure was. Perhaps...
  21. Wanted: Konica Minolta OT-503 Output/Exit tray for Biz C754, C552, Etc etc

    Anyone have new or better yet used output tray for the following models. This is the tray that goes in place of the finisher transport bed and pages lay on it when they exit. The tray comes with a...
  22. Replies
    4
    Views
    217

    [CQ] Re: Scan/copy tilted to the left

    adjust screw on right hinge (standing in front of machine). The adj screw sits horizonal.

    Best to get service manual which shows proper adjustment procedure
  23. Replies
    6
    Views
    191

    Re: Firmware Konica 364e PT

    We have been requesting that members asking for firmware & service manuals make a small donation of $5 or $10 to this website than someone will send it.
  24. Replies
    14
    Views
    707

    Re: Bizhub 363 toner not adhering

    Like others have said

    1) aftermarket toner

    2) aftermarket rollers

    3) always change thermistors, toner build up on thermistors is what causes the cuts in UFR to begin with. Don't even try to...
  25. Thread: HP LJ 600 M602

    by copyman
    Replies
    5
    Views
    548

    Re: HP LJ 600 M602

    If you were able to test motors, etc than I would look at formatter pwb being bad
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4