Search:

Type: Posts; User: repn1999

Page 1 of 13 1 2 3 4

Search: Search took 0.02 seconds.

  1. Re: How to calibrate drums of Sharp machines (MX-2640N)

    SO I would definitely do a FULL calibration on this as suggested. BEFORE you do it.....clean the density sensors....and run a dv refresh 44-17, then do 50-10 adj for the trays. NOT 50-28. if these...
  2. Replies
    1
    Views
    188

    SHARP MX6050N CPFD1N jamming

    I have a Sharp MX6050N machine in the field with a history of CPFD1_N jamming. Machine is outfitted with 3 tray desk plus the machine try for a total of 4, with a rb25 and saddle stitch finisher....
  3. Replies
    11
    Views
    846

    Re: Sharp mx m 654N

    on some machines you can get it to scan color if you put a sheet of paper on top of the check. i believe the guideline is that it has to be plus or minus 20 percent in size if color to prevent...
  4. Replies
    4
    Views
    474

    Re: sharp mx 5001n fan

    be sure to check the screws on the ducts to make sure they are tight. that will cause a similar sound to a bad fan and you will end up ordering a fan for nothing. also for what its worth I would just...
  5. Re: MX5111N Copy quality automatically adjusting after every copy

    this does use a jig. It is the same one as the 3501-5001 used. I am a factory trained tech on this model so Iíve seen it a lot lol probably more than I want to.
  6. Re: MX5111N Copy quality automatically adjusting after every copy

    I agree with the post about new supplies. Another thing to check is are the density sensors clean and are there no scratches on the pri belt where the patches run that are looked at by the density...
  7. Replies
    12
    Views
    633

    Re: Printer MX-4111 not turning on

    Orange light means something is up with the dc power supply. Replace that. They are known to go bad. Same thing for cycling green orange light.
  8. Replies
    1
    Views
    402

    MXM3050 and MXM3070 msata images needed

    does anyone have a factory image for the msata card for a Sharp MXM3050 and a MXM3070? I would really appreciate it if someone could hook me up with them. I have a bunch of sd card and msata images...
  9. Replies
    4
    Views
    474

    Re: Sharp MX3640 fuser noise

    They are brand new units from sharp and they have been tested in other machines where they work fine. Client runs health care type forms and no bleed to speak of just mostly bw text. Very rarely even...
  10. Replies
    4
    Views
    474

    Sharp MX3640 fuser noise

    So I have a mx3640 that continues to build toner and make the screeching noise like the web is locking up. I have confirmed that the client is not running machine out of spec or heavy coverage or...
  11. Replies
    6
    Views
    871

    Re: MX M453 "Remove paper from offset tray"

    replace the tray height sensors...i believe there are 3 and check the harness to the paper detect sensor on the tray. if the harness is not routed correctly it can get stretched and will cause that...
  12. Re: Looking for MX-3140n Firmware/Manual - HDD Replacement

    I just deleted some. Message me if you need to.
  13. Replies
    20
    Views
    2,101

    Re: MX-3610 color and calibration problem.

    Dumb question....Did you happen to check the density on the print and copy settings and make sure they are on defaults? I had a tech who wouldnt change out supplies and reset the counters...and when...
  14. Replies
    16
    Views
    2,639

    [Error Code] Re: MX4071 PHOENIX II SERIES E7-90 codes

    I would recommend replacing the Mini EMMC (smaller MSATA) card. I have seen corruption issues on the new eMMC drives on most of the new models unfortunately and have replaced several. I would also...
  15. Replies
    5
    Views
    577

    Re: MX3140 Desk unit trouble with some trays

    I know the issue is resolved from a previous post...but I would strongly recommend replacing all sensors in the feed units ANY time you have an issue whether that sensor is effected or not. This is a...
  16. Replies
    7
    Views
    887

    Re: MX6070N not keeping network settings

    I would say try a CN update with the latest version of firmware. IF this is an older MX6070 check the label on the MSATA drive on the MFPC PWB. IF the label says lower than v4.0 firmware I would...
  17. Replies
    8
    Views
    528

    Re: MX-M363 background and poor image

    I would say try swapping the dv unit. Your pic isnt the best but looks to me like lines/voids that match the surface of the dv unit are in the background. may have a dv unit rotation issue....I have...
  18. Re: Looking for MX-3140n Firmware/Manual - HDD Replacement

    I have them. I also have SD card images for this series. Please advise whether your machine has a data security kit on it or not. I need to know this before I provide any software so you dont end end...
  19. Replies
    2
    Views
    2,927

    Re: Sharp tech needed Northern California

    Are you still looking for a Sharp tech? I would be willing to relocate for the right opportunity. I am factory trained and fully certified on all current models. I was also a master tech regional...
  20. Replies
    3
    Views
    565

    Re: Sharp MX-M654N

    Excellent machine.....recognized among all manufacturers as a top performer and robust beast in the segment. Pretty technician friendly....stay up on the maintenance and you will be fine. My machines...
  21. Replies
    12
    Views
    1,113

    Re: Sharp MX-M753n

    Like the other guys have said, these are older but built like tanks. All of the dragon series was...and now the newer taurus series (mxm754,mxm6750) continue the durability these machines were known...
  22. Replies
    3
    Views
    528

    KIP 7100 wide format parts guide needed

    does anyone have a kip 7100 wide format parts guide they can hook me up with? thanks in advance
  23. Replies
    17
    Views
    3,358

    Re: Interesting find: Msata cards

    [QUOTE=bigdaddyooo;1435100]


    First I was addressing the comment someone made about swapping msata cards from another machine. Second....the reason you are having to CN update the cards is...
  24. Replies
    14
    Views
    1,052

    Re: DSPF 2 to 2 lead edge is way off side 1 only

    so this only happens on side 1. can you reproduce the same random position issue by scanning from platten glass, since side 1 is read from ccd. if so then that would rule out dspf mechanical and...
  25. Re: fn-18 intermittently stops in saddle stitch

    I know this is gonna sound elementary but I would double check to make sure the machine and finisher are level (just because the plastic looks level it may not be. some machines may have to look not...
Results 1 to 25 of 309
Page 1 of 13 1 2 3 4