Search:

Type: Posts; User: scanmc

Page 1 of 4 1 2 3 4

Search: Search took 0.12 seconds.

  1. Re: Can Konica supplies be made to fit in a Muratec?

    We just buy all Muratec K drums for that series machines then replace them with a color chip purchased from one of the aftermarket suppliers if your going to use them in the CMY slots. The drums are...
  2. Re: Can Konica supplies be made to fit in a Muratec?

    I've done the end cap switch on the toners in a pinch with the Konica brand. This series toner cartridge is not chipped. As far as drums are concerned we have always just purchased the K Muratec...
  3. Replies
    4
    Views
    522

    [Misc] Re: Konica C258 Color drum conversion

    Bummer. Yep that's what I thought was going on.

    Thanks for the input.
  4. Replies
    4
    Views
    522

    [Misc] Konica C258 Color drum conversion

    Yesterday I tried to convert a C258 K drum unit into a color unit via the drum reset chip and removing the small plastic plastic piece that stops the unit from sliding in all the way in the color...
  5. Replies
    5
    Views
    641

    [CQ] Re: Oki c9655 colour misregistration

    I learned my lesson years ago to only use OKI supplies. I woulds say if it happened after the user installed the non OKI drum units that's your culprit
  6. Replies
    0
    Views
    305

    [Wanted] CS1635 Doc Feed Harness

    Does anyone have one of these beauties laying around on the shelf?
  7. Replies
    2
    Views
    811

    Re: Muratec MFX-3535 Turns on/off

    Did you try a new power supply?
  8. Replies
    4
    Views
    951

    Re: Looking for OKI Tech in Chicago Area

    Dealer Locator | OKI Data Americas
  9. Replies
    4
    Views
    523

    Re: CS-221 Developer / DV Unit ????

    One more thing, Also make sure the mirrors are clean especially if the copies are light down the center. The fuser has a tendency to leave a hazy film on the mirrors since it sits right bellow them....
  10. Replies
    4
    Views
    523

    Re: CS-221 Developer / DV Unit ????

    I know on the old CS2030 the developer was changed out of the dv unit.If I recall on the CS 2050 -2550 series these machines were a mono component machine where the toner\dv was all in one. On these...
  11. Thread: MPC5502

    by scanmc
    Replies
    2
    Views
    317

    [Misc] Re: MPC5502

    Thanks! Found it
  12. Thread: MPC5502

    by scanmc
    Replies
    2
    Views
    317

    [Misc] MPC5502

    Good afternoon. I'm looking for the part number for the top half of the case that the transfer roller sits in. This customer seems to have gotten aggressive and slammed the door shut breaking the...
  13. Re: Oki MC860 optional paper tray parts catalog required

    I checked on the OKI website and I don't see any parts list for the optional tray. I do have a parts machine in the back but by looking at your location that might be an issue getting it to you.
  14. Replies
    0
    Views
    346

    [For Sale] Muratec MFXC2828 OEM Supplies

    Make an offer

    2-Black toners
    1-Magenta toner
    1-Cyan toner
    1-Yellow toner
    1-Waste container
    1-Cyan dv unit
  15. Thread: Ricoh MPC5501

    by scanmc
    Replies
    8
    Views
    527

    [Jamming] Re: Ricoh MPC5501

    Well It ended up being the gate shaft and bushings were so gummed up that the solenoid would open or close properly. After a good cleaning she's working like a champ again. You would thing after all...
  16. Thread: Ricoh MPC5501

    by scanmc
    Replies
    8
    Views
    527

    [Jamming] Re: Ricoh MPC5501

    Thanks for the info. Heading back out here today for a closer look.
  17. Thread: Ricoh MPC5501

    by scanmc
    Replies
    8
    Views
    527

    [Jamming] Ricoh MPC5501

    I don't do a lot of work on Ricoh's but I've got this one out in the field. My issue is when duplexing the machine gets about an inch out of the fuser when entering the bridge then jams (J024 code) I...
  18. Replies
    4
    Views
    1,337

    Re: MFX-C2280 doc feeder

    Possibly something up with the HDD?
  19. Replies
    4
    Views
    1,337

    Re: MFX-C2280 doc feeder

    Like your avatar go Cubs! Does the machine actually jam when scanning to the user box or does it just kinda die in the middle of it?

    Maybe one of our Konica Minolta techs has a suggestion. This...
  20. [Misc] Re: Oki C610n Network Software Needed (Module I/F 00.18)

    Took a look on the bpx site and nothing on the knowledge base for firmware on the C610N. You may need to contact OKI support to see if they can help
  21. Thread: Bizhub 4422

    by scanmc
    Replies
    5
    Views
    786

    [Misc] Re: Bizhub 4422

    Thanks for the replies. Think I'm going stay clear from these if the adf's are weak as the customer will be scanning a fair amount.
  22. Thread: Bizhub 4422

    by scanmc
    Replies
    5
    Views
    786

    [Misc] Bizhub 4422

    Looking to place 6 of these in a chain store where space is limited. Customer is in need of a small machine that can do 5-10K a month. My question is what kind of experience has anyone one had with...
  23. Thread: Biz 25e

    by scanmc
    Replies
    12
    Views
    815

    Re: Biz 25e

    This is a Muratec MFX3530/3590 Only way to reset is with a new drum unit
  24. Replies
    3
    Views
    490

    Re: HP Enterprise M605N

    Not sure on that code but fuser errors are usually a 50'S error. Possibly try reloading the firmware
  25. Replies
    0
    Views
    419

    Samsung CLX 9252 image rotation

    While using the feeder the image orientation is fine but as us as you put the paper on the glass in the same direction the machine wants to rotate the image . This just started happening out of the...
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4