Search:

Type: Posts; User: anothertech

Page 1 of 20 1 2 3 4

Search: Search took 0.30 seconds.

  1. Re: Ricoh PRO 8120S has an error code SC401-01

    Oh boy, I think we are on to something here. Might you try an actual Ricoh Drum?
  2. Re: Document Feeder not sensing document in feeder

    Go into IO mode and check the sensors that sense if the ADF is up on down. I think there are two sensors for the up/down of the unit.
  3. Replies
    3
    Views
    200

    Re: sc820 on a SP5210 SR

    I was wondering if it could be a bad RAM chip or a bad HDD, if this kind of machine has one.
  4. Re: Savin 5055 / Ricoh 6054, "Replace Fusing Belt Unit"

    They probably don't know how to get into "simulation"
  5. Replies
    10
    Views
    264

    Re: Ricoh c751 error sc 685

    Once you get it fixed, get surge suppressors on those machines.
  6. Replies
    15
    Views
    570

    Re: MP C4503 Finisher error

    Check to make sure the flag is going into the sensor that senses the tray lower limit, make sure the tray is not crooked and jacked up on the rear side. Also the harness is a little too short and...
  7. Replies
    12
    Views
    546

    Re: blank copy on mpc 3001

    So, what is the working theory for this fix? Maybe the yellow charge arcing and loading down the high voltage?
  8. Replies
    22
    Views
    529

    Re: Ricoh MP 201 NVRAM Removal Procedure

    It looks to me that there is not a removable NVRAM chip on that BICU board.
  9. Replies
    9
    Views
    280

    Re: mpc5503 with sc541-02

    Before you change any PCB's, inspect the ITB for rips, clean the ITB unit, could be arcing. Also check the power outlet, dose it have a surge protector that records power events?
  10. Replies
    20
    Views
    465

    Re: Ricoh Pro C5100s cyan issue.

    Replace the developer. Do a good job getting all of the old developer out, keep turning the unit and vacuuming till it's all out. Bang it, shake it, turn it upside down, clean the doctor blade, then...
  11. Replies
    15
    Views
    490

    Re: Ricoh mpc 4504 jamming

    Sometimes it helps us help you if you post the jam code.
  12. Replies
    22
    Views
    554

    [Misc] Re: Format Hard Disk

    Can you take down the information that you posted on getting into service mode? It's not public information.
  13. Replies
    12
    Views
    546

    Re: blank copy on mpc 3001

    Make a color copy with lots of coverage, stop the copier during the run, just open the door while it's running. Look to see if you have any toner image on the ITB belt, if no then look to see if you...
  14. Replies
    22
    Views
    554

    [Misc] Re: Format Hard Disk

    The answer is, no you can not get into service mode.

    This is for trained techs only, you need to call a tech to come perform this service for you.
  15. Re: Those $#%@#% foam rollers on ricoh finishers.

    They are easy to replace, just check them on the 600K pm.
  16. Replies
    23
    Views
    602

    Re: Mp2852 firmware update problem

    I wish you would tell my coworkers that, they just was to update whatever is causing them a problem today, not worrying about tomorrow.

    I think it's better to be proactive with firmware but most...
  17. Replies
    12
    Views
    401

    Re: JAM 027 in ricoh pro 8120s, help!!

    1+ on the possible bad motor, I had a Pro 8100 give me that kind of jamming, every time I thought I had it fixed I had to have the customer run it while I hung around, after a few thousand copies it...
  18. Re: Error code all ricoh MP C3002/5502/3003/3503/

    I don't miss stringing those cables, used to be a pretty regular thing once the machines started getting old.

    When I started fixing copiers I had half a trunk full of manuals, then we went to...
  19. Replies
    12
    Views
    401

    Re: JAM 027 in ricoh pro 8120s, help!!

    45881

    Item 3 could be the culprit. The wires start to break where they go to the connector at the rear of the drawer unit, usually causes an intermittent problem. Check them closely, sometimes the...
  20. Replies
    18
    Views
    449

    Re: mpc2800 5" lines

    Run individual colors one at a time to see if it's one of the drums.
  21. Re: MPC3503,MPC3504,MPC3504EX? What is different/new?

    Yes, just turn on SP5886-111
  22. Replies
    7
    Views
    444

    Re: Mp 1350 reduce speed

    Is the machine jamming? Be prepared to replace the registration roller when running NCR on this model. It's kind of a pain to get the registration assy out.
  23. Replies
    20
    Views
    1,091

    Re: Ricoh MP C3003 iding noise

    Hytec is excellent for board repair, they even update board firmware that is not upgrade-able in the field. They typically charge half the price Ricoh will charge for a new board. Well worth the...
  24. Replies
    5
    Views
    272

    Re: mp 2852 sc 670 error

    Try it with the harddrive disconnected.
  25. Replies
    20
    Views
    1,091

    Re: Ricoh MP C3003 iding noise

    Go in to service mode and run the motors in I/O mode, you should be able to narrow it down.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4