Search:

Type: Posts; User: Gift

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. Re: optics cleaning cloth + platen glass slippery product

    Blast from the past ;)
  2. Thread: C3100P Issues

    by Gift
    Replies
    11
    Views
    327

    [Misc] Re: C3100P Issues

    is this re produceable if you check the printer with laptop/cross cable? Network speed setting or disable energy-saving features within the network switch can fix this kind of issues.
  3. Re: optics cleaning cloth + platen glass slippery product

    I recall a glass cleaner that looked like "milk", it did both clean and lubricate the glass plate - it was pretty common back in the days but afaik there's just a dealer located in germany who sells...
  4. Replies
    5
    Views
    305

    Re: Bizhub c250i squeaking noise

    See if the noise disappears if you fiddle around the idle rollers away from the paper exit rollers.
  5. Thread: DR314K vs DR313K

    by Gift
    Replies
    5
    Views
    268

    Re: DR314K vs DR313K

    It would require some work and modification/parts swapping because there are several differences "built-wise" like different lenght of the waste toner exit thingy, charge plate, etc. It's probably...
  6. Re: mpc3003 offset (ghost image) after sleeve unit replaced

    We also have this every now and then - some sorts of paper/enviroments aren't running well without a little "temp boost". I think normal paper setting is used to a maximum of 81g/m2 - not much of a...
  7. [CQ] Re: MP2851 light print jobs and "Add Toner" message

    Since the issue accured after a toner bottle change I'd still take a look at the hopper/bottle - berhaps the caps from the old bottle sits on top of the cap from the new bottle. Also check if the...
  8. Re: ricoh mp 3350 unable to detect in android connector after phone restore

    Can you see the web interface on your phone? If not check your wlan settings.
  9. Thread: New MP 301 drums

    by Gift
    Replies
    18
    Views
    888

    Re: New MP 301 drums

    We startet using the Type1515 units when the MP301 started but had way too much issues right from the start - kind of like the problems you can get with the correct units supposed for that model but...
  10. Replies
    20
    Views
    585

    Re: mp4002 dirty egde, only lateraly

    Bad drum shaft grounding can also increase this issue. How does the dv mag roller looks like? IIRC it kind of became coated black with toner and needed to be cleaned after 60-80k. Since you have to...
  11. Replies
    14
    Views
    400

    [Misc] Re: MPC 3002 paper exit problem

    -> Insert Picard Facepalm here <-
  12. Replies
    8
    Views
    299

    Re: Ricoh MPC 5504 exit jams

    Does the unit have a 1 bin tray installed? You can try and remove the finisher/bridge and let the customer test it without these options or in case you can get there quick just ask them to call you...
  13. Replies
    14
    Views
    400

    [Misc] Re: MPC 3002 paper exit problem

    Lol print quality does also not look very nice ;)

    It's indeed an issue with the paper/enviroment - you can try to mc-gyverfy* the internal output tray or order the modified one (I think that came...
  14. Replies
    46
    Views
    1,643

    Re: Bizhub 364e - clicking/knocking noise at idle

    I'd also swap the bearing because you'll have to remove them anyways for lubricating the pressure roller axis. Haven't bought any for km but these are usually some generic stuff so not really hard to...
  15. Thread: New MP 301 drums

    by Gift
    Replies
    18
    Views
    888

    Re: New MP 301 drums

    Urgh... my condolences^^
  16. Replies
    16
    Views
    743

    Re: Technical Service and Support (Octopus)

    Yeah, still working on that but there's so much other stuff going on right know. 2 of my collegues got their account managed. I'd suggest you better get in touch with ricoh.
  17. Replies
    12
    Views
    488

    Re: Mp c5503 exit jam & fuser pressure cycles

    Thanks for posting the solution, I'll keep that in mind in case we won't have luck with the drive repair.
  18. Thread: New MP 301 drums

    by Gift
    Replies
    18
    Views
    888

    Re: New MP 301 drums

    Indeed, perhaps this is just a late april joke - we managed to swap most MP301 by now ;):p
  19. Replies
    46
    Views
    1,643

    Re: Bizhub 364e - clicking/knocking noise at idle

    For loud knocking noises it's usually not a lack of lubrication within the bearing but between the contact surface of the bearings inner ring and the pressure/heating-roller it sits on. Materials...
  20. Replies
    46
    Views
    1,643

    Re: Bizhub 364e - clicking/knocking noise at idle

    You can use WD40 PTFE Specialist to lubricate the bearings. Might work or not, depends on how the overall condition of the fuser looks like. Ususally this knocking sounds comes from a lack of...
  21. Thread: Stress level

    by Gift
    Replies
    16
    Views
    917

    [Misc] Re: Stress level

    Probably too much spare time and not enough balls to go out and participate in something real. I stopped social networking and online politics discussions years ago and that did really helped me...
  22. Replies
    12
    Views
    488

    Re: Mp c5503 exit jam & fuser pressure cycles

    We had a few faulty fuser drive assys failing - it's basicly just some one-way pulley and a torque limiter you can order to fix them.
    Errors usally are weird SCs and Fuser Jams. The torque / one way...
  23. Re: mp c6003 charge roller assemblies -lines, lines, lines

    I find these refurb kits that includes all parts (not just the charge roller) not that bad. From my experience they work "ok" for the slower models (100-150k prints) and not very well in faster...
  24. Replies
    9
    Views
    296

    Re: Flat cable repairs

    Yeah that worked for my too in some occasions (or kind of saved my ass). Unfortunately flat cables on newer MFPs are built even more thinner/delicate so this "dirty fix" is getting harder to perform.
  25. Replies
    13
    Views
    708

    Re: tape problem on PC417

    +1 for the bracket adjustment, we also had some PC417 jamming directly out of the box
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4