Search:

Type: Posts; User: allan

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Re: C458 with blue LEDs below control panel lit all the time

    Unplug the network cable then start it up to see if the data light stays on. Does the LED's start blinking if you send a job? Does it have a fax kit installed?

    You can unplug the LED connector for...
  2. Replies
    3
    Views
    315

    Re: Konica pro tech needed 951 and 1100

    Know just the guy but already working there. pro techs...
    Not a lot of them around.

    Especially the kind of tech that goes out of his way to resolve issues. You know resourceful and keeps them...
  3. Replies
    9
    Views
    367

    Re: Auto Dealer Window Sticker Printer

    A brother label printer comes to mind. Had good fun with there before.

    If B/W is requiered run of rolls of thermal sticker paper. Thermal printers are fast these days.
  4. Re: Konica C284e "Preparing to connect to external server please wait"

    If User auth and ID and print is used make sure it authenticates on the machine only. There is an option to select an external server. Make sure its set to authenticate on devise only.
  5. Thread: Stress level

    by allan
    Replies
    16
    Views
    917

    [Misc] Re: Stress level

    Also stopped participating in those threads. Its pointless to try and change a set mind about there fatalistic outlook.
    Been polarizing people that used to get along just fine before.
  6. Replies
    46
    Views
    1,643

    Re: Bizhub 364e - clicking/knocking noise at idle

    You can remove the flange. Screwdriver(s) The gap in the ring gives it away.
    Yes you need that exact one. The flange is offset from the edge. Others are flush with it.
    They are super common on the...
  7. Replies
    46
    Views
    1,643

    Re: Bizhub 364e - clicking/knocking noise at idle

    There is a groove in the bearing. The flange is a snap ring that gets snapped into the groove. The gap does not serve a purpose.
  8. Replies
    5
    Views
    233

    Re: Red line on edges of paper

    Could be corrosion or dirt on the grid. Like mentioned change tat out as soon as possible.
  9. Poll: Re: What brands of Copiers/MFP's are you working on v2.0?

    Poll results are adding up to more than 100%....
  10. Replies
    9
    Views
    296

    Re: Flat cable repairs

    Cut it with scissors and scrape of the insulation with a razor blade if you need to flow a thin layer of solder on the the new exposed copper.
  11. Replies
    46
    Views
    1,643

    Re: Bizhub 364e - clicking/knocking noise at idle

    you local fastener shop should have those bearings for a lot cheaper.
  12. Replies
    7
    Views
    294

    Re: Load LT-R and press [START]

    Is it on the latest firmware? Can they not just change it out to a tray or can the other media not print on the bypass.
    This should be fixable i hope. That would have been an over sight from the...
  13. Replies
    46
    Views
    1,643

    Re: Bizhub 364e - clicking/knocking noise at idle

    Dig into the fuser and check if its as simple as a bearing. Those bearings can be bought from any bearing supplier.
    Is its something else that can be found in a kit? Get a kit and replace only the...
  14. Replies
    8
    Views
    367

    Re: issue with FS-534

    Then must be on the stapler unit itself as mentioned . When a new cartridge is installed it will staple 5 times. Not sure if it will do it even if you manual advance the staples then installing it....
  15. Replies
    46
    Views
    1,643

    Re: Bizhub 364e - clicking/knocking noise at idle

    Yes you get some real comprehensive and quality rebuild kits out there. Cost less than 1/3 of a new unit.
  16. Thread: Pros Elite 100

    by allan
    Replies
    3
    Views
    3,111

    Re: Pros Elite 100

    I felt exactly like that when I worked a 500 Kilometer or roughly 300 Miles radius area. Manager phoned me up one morning telling me that the boss is real upset after pulling a report from the...
  17. Replies
    14
    Views
    418

    [Misc] Re: KM C454e Light spots on blue prints

    Wanted to try that. Can get a bunch of DV613K that is stuck in a suppliers stock, that means cost price or less.
    What was the ill effect you had on the C454?

    End of side track...
  18. Replies
    14
    Views
    418

    [Misc] Re: KM C454e Light spots on blue prints

    Clean your mag roller. Got some kind of contaminant on it like oil.
  19. Replies
    17
    Views
    820

    Re: KM-3252ci black only banding issue crossfeed

    Looks like 2 things not happening correctly. Leaking charge current and not discharging.
    If not a component problem on the HVT then a wonky contact somewhere.
  20. Re: Konica 1250 toner piles on charging unit sides after 5000 copies

    If its done its yield or close to it. Not much to go wrong on the transfer belt assy.
    The toner dusting in that area would suggest a problem on the cleaning unit the cause of it is unknown but check...
  21. Replies
    22
    Views
    3,880

    Re: What happens to the developer?

    What a waste... Yea been doing it. Pity the waste from 754 will not be good for a 423.
    Had to do it for my 951 machines due to shortages and no ill effect. Sure its not the best to keep your...
  22. Replies
    22
    Views
    3,880

    Re: What happens to the developer?

    Can't help it i have to spill.

    Developer does get #u&ed in more than one way. The sharp corners for the grains gets warn down and your nice and puffy mag brush is not the same anymore and these...
  23. Replies
    22
    Views
    3,880

    Re: What happens to the developer?

    Yea and i am the guilty one reusing the developer....
  24. Replies
    6
    Views
    310

    [Jamming] Re: Bizhub 223 Tray 1 Jams

    That would block the path for double sided printing as well.
  25. Replies
    6
    Views
    310

    [Jamming] Re: Bizhub 223 Tray 1 Jams

    On the 423 there is an additional photo reflective sensor on paper feed unit 2 (item 19 on page 41 of parts manual). Remember that there was some kind of issue installing that on 363/223. I think its...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4