Search:

Type: Posts; User: tsbservice

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    176

    Re: Ricoh mp c2003 . Error

    slimslob. As usual you are spot on. My advice to him was much more in general.
    We will see but lots of fine folks are watching him towards better side.
  2. Replies
    6
    Views
    176

    Re: Ricoh mp c2003 . Error

    Leonardo dovresti fare degli sforzi nei tuoi post almeno prova a postare in inglese e descrivere quello che hai fatto finora non farÓ male.
    Solo un consiglio amichevole.

    PS
    Mi ci sono voluti 2...
  3. Replies
    4
    Views
    199

    Re: Toshiba estudio 455 motor

    Lower speed models have different motor than 355/455. However it looks like 356/456 motor is the same if you have any.
  4. Replies
    14
    Views
    612

    Re: C-258, unable to load firmware...

    You took it right OC, it will display NG complaining about optional memory I see it many times. I for sure won't left machine with old firmware to go out of my hands.
    Did you try it with door open?...
  5. Re: Brother MFC L8850-cdw how to reset Paper Feed PF-1 kit counter

    Enter Maintenance mode use 88 code scroll to correct consumable to reset press set it will ask to confirm counter clear press set again. Stop to exit and 77 to printout Maintenance list and check...
  6. Replies
    35
    Views
    1,539

    Re: Kyocera 3645 not grabbing an IP address.

    Great, tmaged advice.
  7. Re: [Image Quality] Thin line won't go away on Konica bizhub Press C6000

    Picture 1(as far as I can see) has two arrows with remarks clearly describing white line isn't issue.
  8. Replies
    3
    Views
    165

    [Error Code] Re: error c5360 km c308

    You're welcome :)
  9. Replies
    3
    Views
    165

    [Error Code] Re: error c5360 km c308

    System 2 - 3rd page - Clean unit setting - should be Not Installed
  10. Thread: hey peeps!

    by tsbservice
    Replies
    5
    Views
    156

    Re: hey peeps!

    Welcome
  11. Re: c454e all color's drum and installation error

    Then FSB or controller board.
  12. Re: c454e all color's drum and installation error

    Cra.py pictures but I guess it's is giving "Yellow drum installation error" message.
    Had one C258 same situation but very intermittent may be bad drum lock lever or wiring harness never find.
    Had...
  13. Replies
    9
    Views
    355

    [Jamming] Re: Bizhub 364e strange jamming problem

    Thanks for that clarification I feel your pain. The one of the reasons I asked I have almost similar machine except total counter is x5 and never experienced (thanks God) such a jamming issue.
  14. Replies
    35
    Views
    1,539

    Re: Kyocera 3645 not grabbing an IP address.

    See below Billy, we may have to wait though.
  15. Replies
    9
    Views
    355

    [Jamming] Re: Bizhub 364e strange jamming problem

    Interesting thread. I wish we have also - total counter, parts life and jam history to make picture little bigger.
  16. [Misc] Re: user trying to scan a check and it shows up blurry? all other scans work fine.

    Even in every user manual.
    OP tell them to use solution 1 from BC's tutorage.
  17. Replies
    5,904
    Views
    1,257,086

    [Funny] Re: Joke of the Day

    And what is making sweet 'caramel' hard 'criminal' :cool:
  18. Replies
    14
    Views
    612

    Re: C-258, unable to load firmware...

    I would conduct Self-diagnostic (if it still fails to load with front door open).

    Procedure (using SERVICE MODE menu)
    1. Call the Service Mode to the screen.
    2. Touch these keys in this order:...
  19. Replies
    1,332
    Views
    107,335

    Re: Need some advice on learning networking

    Last sentence really make me laugh... because that's exactly what my wife keeps telling me 😂
    Back on track I didn't talk about regular IT but a few special who learnt my respect over the time.
    I'm...
  20. Replies
    1,332
    Views
    107,335

    Re: Need some advice on learning networking

    Because too many ITs will leave no room for regular techs. I'm joking but it appears to me lately everyone wants to be an IT work remotely get high paid etc. And that said they even don't understand...
  21. Replies
    14
    Views
    612

    Re: C-258, unable to load firmware...

    Huhh.... right I believe OC was doing mostly Toshy in the past but he should be familiar now with most KMs.
    I would try loading FW with front door open. Also 8 series there is no SSD instead they...
  22. Replies
    3
    Views
    194

    Re: Need Konica C70HC service manual

    You don't have to excuse. My point is to keep forum organized and tidy as much as possible. That will make things easier to find and folks happy :)
  23. Replies
    3
    Views
    194

    Re: Need Konica C70HC service manual

    You may post your request here where more techs with manuals can see it.
    https://www.copytechnet.com/forums/service-manual-requests/
  24. Replies
    1,332
    Views
    107,335

    Re: Need some advice on learning networking

    My understanding of networking is very limited but I would rely on experience and knowledge of rthonpm anytime.
    His words weight nothing but gold.
  25. Replies
    35
    Views
    1,539

    Re: Kyocera 3645 not grabbing an IP address.

    Old dogs can learn new tricks.
    I never assume anything as granted you can learn new things every day and that makes life so wonderful :)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4