Search:

Type: Posts; User: GUNit

Search: Search took 0.09 seconds.

  1. Replies
    9
    Views
    1,486

    Re: TA8001i Exit rollers running in reverse

    doing it on copy jobs too. strange how replacing the door fixed it for 3 months and believe me this machine gets used alot so you would think it would have come back before then. also i did the...
  2. Replies
    9
    Views
    1,486

    Re: TA8001i Exit rollers running in reverse

    hi

    yes we have this scenario also. had it approx 3 months ago, changed right hand door with a working machine- no good. changed with a brand new door and problem gone for 3 months, but now...
  3. Re: looking for Kyocera/Develop trained engineer in Birmingham England

    sorry guys position filled
  4. looking for Kyocera/Develop trained engineer in Birmingham England

    working on latest machines in Kyocera and Develop range. PM me if interested
  5. Thread: C224e J3003

    by GUNit
    Replies
    27
    Views
    7,809

    [Jamming] Re: C224e J3003

    Just had this yesterday so thought i would put it out there. Jamming intermittently at reg and sometimes skewing and varying registration. went through the usual but what i found was if you take out...
  6. Replies
    10
    Views
    2,092

    Re: KM-3035 Firmware Headache

    its been a while but i seem to remember you have to pull the print card out when doing the machine firmware or it doesnt work.
  7. Thread: Kyocera

    by GUNit
    Replies
    9
    Views
    819

    Re: Kyocera

    maybe this is just a UK problem, as i notice jhalfhide is uk based as am i. i have been with Kyocera from C830 and C2630 days to the present garbage they sell and although you can only speak on a...
  8. Thread: Kyocera

    by GUNit
    Replies
    9
    Views
    819

    Re: Kyocera

    im with jhalfhide on this one. we were Mita dealers in the early days when 3035 and the like were king . ever since Kyocera took over i agree toner yields are terrible very expensive to run ie toner...
  9. Replies
    30
    Views
    5,436

    Re: *&%&%& 3050ci with skewed image.. HELP

    just wondering what its like if you do single colour cyan or magenta will it be skewed as there are 4 individual lasers just wondering now if someone has maybe been playing with the allen screws on...
  10. Replies
    30
    Views
    5,436

    Re: *&%&%& 3050ci with skewed image.. HELP

    if the image is skewed on the transfer belt then you can discount paper feed. if internal prints are skewed then discount optics which leaves engine more than likely laser, maybe not seated correctly...
  11. Replies
    4
    Views
    581

    [CQ] Re: 4500i dot/marks on pages

    they are quite some marks. i would think marks that heavy would be easily seen on say a drum or transfer belt etc. could it be some kind of electrical noise/interference on mains? the only thing...
  12. Replies
    51
    Views
    8,040

    Re: Zeus Feed Rollers

    Been doing this for a while now with great success. the neoprene compound works so much better on the Kyoceras. use them wherever you can from printers to small mfps to the 8000is. on some they just...
  13. Replies
    3
    Views
    769

    Re: km 3050ci noise from laser cleaner

    Take the lsu back out just enough to get to the motor and then wrap tape around it. this is in the alfard troubleshooting guide, I think they recommend using the orange filament tape but insulating...
  14. Replies
    11
    Views
    2,094

    Re: 520I stuck in welcome screen

    had this before and it turned out to be boot dim on the main pcb, good luck
  15. Replies
    9
    Views
    20,820

    Re: C5101. error on Ta4550ci

    Think the general rule to follow is if there is a counter for it then reset it, the great thing about digital is there are so many calibrations and compensations for aging and dirty optics etc going...
  16. Replies
    9
    Views
    20,820

    Re: C5101. error on Ta4550ci

    the fix for this is to reset the charge roller count when it has done over life. unfortunately the majority of engineers when changing the charge roller itself do not reset the count so the machine...
  17. Replies
    5
    Views
    1,023

    Re: DP-750/DP-760 lift plate issue

    had this many times the problem lies in the black holder which houses the pick up roller and feed belt. there is a little plastic piece that snaps off this holds the unit in a position where a sensor...
  18. Thread: Kyocera KM-4035

    by GUNit
    Replies
    5
    Views
    665

    Re: Kyocera KM-4035

    this rings a be it ll im sure you have to change sim 956 from old to new or vice versa something to do with conveyancing section I believe, good luck
  19. Thread: Feed Rollers.

    by GUNit
    Replies
    13
    Views
    2,374

    Re: Feed Rollers.

    think you missed the point here. my problem doesn't lie with buying the rollers or any of the other useless parts Kyocera supply, my problem lies with the quality of the rollers. why have a machine...
  20. Thread: Feed Rollers.

    by GUNit
    Replies
    13
    Views
    2,374

    Re: Feed Rollers.

    these tyres are s..t and are not covered by warranty. they should be in the maintenance kits as they will be needed at 600k. we use Konica tyres which work so much better. sometimes you have to look...
  21. Replies
    6
    Views
    843

    Re: KM 4050 status on display

    if my memory serves me correctly go into system menu then under the copy heading look for priority reservation then enter that and switch it off/on, its along those lines same as ta250ci. hope this...
  22. Replies
    68
    Views
    8,562

    good old salesman

    many years ago we swapped out a canon 400 that was shot. expecting to ditch this beast at the nearest dump you can imagine my surprise when the salesman said he had sold it. ok i thought give me a...
  23. Replies
    14
    Views
    2,092

    try changing sim 956 from new to old works for me...

    try changing sim 956 from new to old works for me every time. should be no need to tweek anything else. good luck
Results 1 to 23 of 23