Search:

Type: Posts; User: srvctec

Page 1 of 12 1 2 3 4

Search: Search took 0.12 seconds; generated 10 minute(s) ago.

  1. Replies
    9
    Views
    867

    Re: bizhub C368 Detail Codes

    Notice I said to ONLY turn off "B", and to leave "C" set to on.

    My theory on this is that if a motor isn't turning for whatever reason (B is for motors and fans), turning off and on the machine or...
  2. Replies
    9
    Views
    867

    Re: bizhub C368 Detail Codes

    Weird that this thread was started when I just had something very similar happen on a 958. The call was jamming but that was not the issue. The machine's display had the white screen with the...
  3. [Misc] Re: C258 Change Drum Units message with 30% life remaining

    Agreed!! On all accounts.
  4. Thread: KM 601

    by srvctec
    Replies
    15
    Views
    1,136

    Re: KM 601

    Yep, that's exactly what I did. I just rummaged through our stash of old bushings and made a few with ground wires I cut off junk machines near the power cord, using the ring/loop end to attach to...
  5. Thread: KM 601

    by srvctec
    Replies
    15
    Views
    1,136

    Re: KM 601

    You're spot on with everything. I went so far as to use a bushing (junked from somewhere) with a ground wire soldered to it, installed on the end of the mag roller to keep it grounded. I never...
  6. Replies
    17
    Views
    785

    Re: C552 colour print issues

    Actually you can access the laser glass when the "drums" (actually IUs for the 3 colors on this machine) are out. With the Y IU out, run the cleaning wand into the proper place and watch from above...
  7. Replies
    12
    Views
    1,076

    Re: Interesting Ozone Filter Question...

    I've never seen any plugged on these larger machines but then we haven't had any placed in super dirty environments, either. I can't remember in the last 30+ years if I've had an o-filter plugged on...
  8. [Misc] Re: Konica Minolta C368 Latest Firmware and Movie File

    Latest base version is X4 and latest movie is G00-90.
  9. Replies
    10
    Views
    1,130

    Re: DF-701 cracked base frame

    Agreed. There is no way that's "normal wear and tear".
  10. Replies
    7
    Views
    733

    Re: Bizhub C-308 with FS-534 finisher...

    I'm confused. The title says FS-534 which is the standard external floor finisher but you mention the internal finisher unless you meant the horizontal unit instead.
  11. Thread: Stethoscope

    by srvctec
    Replies
    9
    Views
    1,985

    Re: Stethoscope

    I bought a stethoscope probably about 20-25 years ago, specifically to use on trying to locate noises in copiers. I think I used it maybe once or twice, mainly because it seemed ridiculous to be...
  12. Replies
    13
    Views
    1,668

    Re: Tech Support Lately

    We sell and service only KM and I dread starting a ticket with the call center, simply because they rarely ever solve anything for us. They are super picky about being trained on the machine but...
  13. [Misc] Re: C258 Change Drum Units message with 30% life remaining

    You can't find the F/W because it's ONLY for authorized, TRAINED service technicians to install. PERIOD.
  14. Replies
    10
    Views
    1,091

    Re: Konica Minolta C458 Printer Area

    Well, usually. I've set up hundreds of machines over the last 30+ years and lots of times there are values already set from the factory prior to me changing a thing. It seems the default used to...
  15. Replies
    4
    Views
    276

    [Jamming] Re: C300i 30-03 Jam code

    Same result from each paper source (all trays including bypass)?

    Is there any additional paper cabinet attached?
  16. Replies
    10
    Views
    1,091

    Re: Konica Minolta C458 Printer Area

    Sounds like an end user got into service mode by Googling how to do it (THE number one reason we as techs should NEVER leave the default CE password set OR turn it off!!!) and cleared all the printer...
  17. Replies
    8
    Views
    506

    Re: Bizhub C227 printing problems

    You failed to mention what version of F/W and what Function version the machine is at. Put the latest F/W on and set FV properly and see if that helps.
  18. Replies
    12
    Views
    1,076

    Re: Interesting Ozone Filter Question...

    I would think washing would not be good because when new, these aluminum o-filters are coated with a flat black substance (I always thought it was a thin coating of charcoal or something similar to...
  19. Replies
    15
    Views
    922

    Re: Bizhub new firmware: marketplace G00-X4

    Huh??! I've updated DOZENS of 8 series (7 and 9 series also) machines to the X4 F/W and never had Marketplace come into play on any of them. Never had a customer complain about anything new after...
  20. Replies
    10
    Views
    1,479

    Re: USB Firmware issues...

    My main F/W install USB stick is a Mushkin 32GB USB 3.0 that I've use for years without issue. Now that all the newer machines just require a folder on the drive vs. a crap-ton of files on the root,...
  21. Replies
    2
    Views
    416

    Re: Bizhub new i-series drums life

    And if you want a third opinion from KM, check out the retail pricing info. It's different than both the parts and service manuals!
  22. Replies
    15
    Views
    1,080

    Re: developer charge problem on C454e

    All of this is happening without any P codes or C codes?
  23. Replies
    4
    Views
    574

    Re: FS-533 Finisher Question

    Well, I'll be darned. It's right there in the service manual and I had no idea that option was there. I learned something today, so thanks for that!
  24. Replies
    7
    Views
    1,180

    Re: 658e prints completely black

    I had this happen on a C558. Broken holder for the charge roller, from the factory. Had to RMA it and get a new drum.
  25. [Misc] Re: USB thumb drive does not work with 4,4e,8,8e or i Series

    We just started using rufus to format thumb drives since Windows is a no no. rufus is open source and works well with a portable version that doesn't need installing.

    Rufus
Results 1 to 25 of 295
Page 1 of 12 1 2 3 4