Probably the write roller that is in contact with the TPH when burning a master. It is rubber and has probably become hard and shrunk due to age. You could clean it with belt cleaner or rubber...
Type: Posts; User: 20gaugeO/U
Probably the write roller that is in contact with the TPH when burning a master. It is rubber and has probably become hard and shrunk due to age. You could clean it with belt cleaner or rubber...
I don't remember and I don't have that old book but whenever you change the TPH on any machine you have to adjust the TPH resistance to match the new one going in. It should be stamped in ohms on...
Anyone using Metallic Gold Ink S-7098??? I have someone that wants to run it but does not want to buy a case of it. If anyone doesn't have a need for an entire case as well or has some they wish to...
Anyone using Metallic Gold Ink S-7098??? I have someone that wants to run it but does not want to buy a case of it. If anyone doesn't have a need for an entire case as well or has some they wish to...
Which drums are compatible?
Are the drums physically the same length? GR 3750's took the longer drum, maybe you have a short FR drum? If they are the same length then remove the cover under the...
Machine is from 1991... remove drum from machine... remove lower plastic cover under the drum handle area... should see a PCB with a row of DIP Switches... if you have a working drum compare the...
Does the machine also have a Fax installed? Shutting the machine off with the switch should fix the error, sometimes these machines just get confused if they are never shut off (used as a Fax always...
C53 is install ink tube. Are you using generic or have a connector not in the right place or fully seated
If it's a J08 it could be nothing but a dirty paper IN sensor. If the copy count is low it may have the original FT and sep pad in it and maybe they just need replacing. Then feed clutch may be...
This sounds familiar but would have happened years ago on a 3050ci flavor... Firmware fixed I believe
Or what happens if you change the paper weight of Cardstock to something different? Or...
Yes it's normal to hit the plastic when opening and closing, but if it's binding on it that's not good. If you haven't done it already you can open the scanner clam shell top and rig the 2 safety...
Some light machine oil or WD-40 like stuff would be fine.
Yes the clamp plate on the drum may be hitting the black and clear plastic cover plates (the ones you lift to remove the cut strip). I...
First put a little oil in the clamp plate open/close gear area on the top of the drum, sometimes that part became gummed up.
Does the motor assy come down and make an attempt to flip over the...
Memory clear -- Turn machine off, hold yellow reset down while turning on the machine, release when beeping and normal sounds stop
The drive pin chuck on the back of the GR/FR drums are probably a...
I don't remember ever running into that plate being bent but from the looks of it it may be nothing more than a grounding contact plate, looks like 1 screw so take it off and see. Doubt it was ever...
Might as well go back to the beginning and ask what model Riso you are using and if you are using the right driver for it and hopefully it's not a Mac you are using. Riso and Mac don't get along all...
Never had an entire TPH go out, let alone twice. Segments go out and fail yes but not the entire thing. Bad board or wall outlet power problem frying it. Is it on a surge???
2 masters on the drum
Ink dried up
Original on glass not face down... keeping it simple cause not sure you have even looked at the machine yet from your description
That plate presses the print drum safety switch. You can go to the back of the machine and bend the actuator a bit so it triggers the switch easier/sooner. After slamming the drum in for years the...
Service Bulletin B293-2K3-0019
[Problem]The “Please install toner container.” message may display even if it is installed correctly.
Field Measure Please replace with new engine PWB if the...
Well, if you set both drums on the table they should be the same length. It should pop a code if the drum is the wrong type installed. I believe all RP's are wide, shorter drums were the smaller RN...
Yep, belt could have jumped a couple teeth and be way out of time. The belts also like to stretch after many years and copies being run on them which can make putting them back in time kind of like...
Never used them. Just grab 1 end with a spring hook firmly and tighten that side down. Then go to the other end, pull it tight tight and lock it down. Then go back to the first end loosen that...
The rubber write roller has shrunk a bit due to age/use. Adjust TM 287 (Master Making Speed Adj) to a slightly more positive (+) value.
So you can run TM 102 and the feed tray cycles all the way up and down???
Now you have the "check feed area" message? When it's displaying this press the * key, it may give a more in depth code (I...