Search:

Type: Posts; User: blackcat4866

Page 1 of 20 1 2 3 4

Search: Search took 0.23 seconds.

  1. Re: Kyocera Ecosys M2635dn MFP/ P2040dn

    The fusers and fuser drive have been an ongoing issue. =^..^=
  2. Replies
    2
    Views
    103

    Re: Kyocera 2-series Question

    Both the xxx2ci and xxx3ci have more vivid colors.

    The original fusers will squeal and give C6220, C6030, C6600 and C6770 errors. A couple of the metal shafts are made of very soft metal and very...
  3. Replies
    8
    Views
    34,403

    [Error Code] Re: Kyocera Taskalfa 4500i Error Code C7460

    Do you have any bent pins in the union connector? =^..^=
  4. Replies
    29
    Views
    667

    Re: Let's Play a Game (Taskalpha 3551ci)

    The original springs are only 9mm long. By the time you stretch them to 17mm they are still not strong enough. With 21mm springs, the rollers and shaft pop right out of the holder of their own...
  5. Replies
    29
    Views
    667

    Re: Let's Play a Game (Taskalpha 3551ci)

    5505ci Skewing from all trays

    *&%&%& 3050ci with skewed image.. HELP

    *&%&%& 3050ci with skewed image.. HELP

    I was only a small voice of that conversation. Credit goes to 20gaugeO/U. ...
  6. Replies
    29
    Views
    667

    Re: Let's Play a Game (Taskalpha 3551ci)

    The same applies equally to the other Alphard family machines. =^..^=
  7. Replies
    29
    Views
    667

    Re: Let's Play a Game (Taskalpha 3551ci)

    Nope. Tray #1 and tray #2 (upper & lower trays in the main body). =^..^=
  8. Replies
    29
    Views
    667

    Re: Let's Play a Game (Taskalpha 3551ci)

    I have a suggestion, if you're ready for another task:

    Compare the feed units between the 355ici and the 5551ci. Take special note of the (5) conveyance rollers on the bottom of the higher speed...
  9. Replies
    13
    Views
    273

    Re: Taskalpha 356ci- Black toner empty

    True. There is a little more to it though.

    If the rubber wiper comes off or is damaged it leaves a layer of unagitated developer setting right on top of the sensor, giving a falsely low reading....
  10. Replies
    1
    Views
    87

    KM-3552ci jams 0512, 0502

    It sorta makes sense when you think about it:

    Here's a machine with 40K on the rollers (and they are NOT flattened, like they could be). Every page from tray #2 jams 0512 or 0502. So I pulled the...
  11. Re: toshiba E Studio 555. code F070 need to reset

    It sounds to me like you've got a paperweight. =^..^=
  12. Replies
    13
    Views
    273

    Re: Taskalpha 356ci- Black toner empty

    I'm having a different read:

    1) I suspect that the toner hopper is working properly taking the toner from the bottle.
    2) If you can pour some toner in manually and satisfy the toner sensor, I...
  13. Replies
    29
    Views
    667

    Re: Let's Play a Game (Taskalpha 3551ci)

    Agreed. The only reason that I've ever changed a Kyocera laser is if the cleaners fail.

    Clean the worm with alcohol then grease with the white lithium grease (not the gear teeth). Make sure that...
  14. Replies
    29
    Views
    667

    Re: Let's Play a Game (Taskalpha 3551ci)

    Yes the individual laser sections are interchangeable.
    =^..^=
  15. Replies
    6
    Views
    176

    Re: MJ-1112 ribbon cable

    Yes, I saw that. If it was HP you'd have to buy the whole finisher. =^..^=
  16. Re: Not a newbie, but TABS tech forums are screwed up

    Welcome! =^..^=
  17. Re: testing my new lap top with this forum

    Its somewhere between 12 and 24 hours in which you can edit a post. After that timespan only the administrator can edit. =^..^=
  18. Replies
    19
    Views
    415

    Re: e-Studio 457, not fusing...

    I wonder why it was so low? Good catch. =^..^=
  19. Replies
    11
    Views
    317

    Re: C554e j12-01

    I had a bizhub 454e that was wearing the separation roller for tray #1 tapered in 15K pages or less. Upon examining the feed assembly you could see that the feed and separation rollers did not make...
  20. Replies
    19
    Views
    415

    Re: e-Studio 457, not fusing...

    Needless to say, the wrong model fuser will cause poor fusing, 30 minute "Please Wait." intervals, and eventually wearing out the helical drive gear on the main motor for hours of continual idling. I...
  21. Replies
    19
    Views
    415

    Re: e-Studio 457, not fusing...

    Three things that I would check:

    1) There are two attachment hooks for the fuser pressure springs ... is it on the tighter setting?
    2) I've had bad lamps before. The machine cannot detect an open...
  22. Replies
    6
    Views
    176

    Re: MJ-1112 ribbon cable

    That's RIBON. It's a Toshiba proprietary application that organizes you parts manuals into a single application. =^..^=
  23. Replies
    4
    Views
    165

    Re: 2540 adding toner

    1/3 to 1/2. Yes, let it run.

    It's mono-component toner, and the developing unit comes empty. Also keep in mind that you'll usually get some mottling when filling the developing unit for the first...
  24. Replies
    1
    Views
    133

    Re: HP vs Canon plotters

    Very similar build. The software for the HP is friendlier, and the error codes seem to point to something specific. On the Canons the service mode is not particularly intuitive, and the error codes...
  25. Replies
    4
    Views
    165

    Re: 2540 adding toner

    I'll bet that you didn't run U130 to fill the new developing unit with toner. I will do it eventually, it will just take a really long time. =^..^=
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4