Search:

Type: Posts; User: driving lots of miles

Page 1 of 10 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    6
    Views
    832

    Re: Sharp mxm 266n

    Here in the middle of the country we have had a lot of issues with high moisture content. open a new ream of paper and see if it still curls.
  2. Replies
    3
    Views
    3,573

    Re: Victor 1260-3

    No marks on the tiny gears we have have seen its much cheaper for them to buy another calculator. I know the customer gets used to their favorite calculator and definitely don't want to change but...
  3. Replies
    9
    Views
    1,185

    Re: M453N indents

    Looks like a fuser issues as previously stated.
  4. Re: MP C2003 how to change print density with Mac

    Would these adjustments not be done in the computer before sending it to the Mp c2003?
  5. Replies
    3
    Views
    3,573

    Re: Victor 1260-3

    On the calculators the boss has had us work on if the timing is off it is almost impossible to redo. We tell the boss its broke and we cant fix it. You could mess with it over three hours and still...
  6. Replies
    8
    Views
    1,390

    Re: Sharp 402SC Print issue-HELP!

    I would try another transfer belt it doesn't look like the cleaning blade is doing its job.
  7. Replies
    10
    Views
    2,586

    [CQ] Re: MX-M364

    I just had a call today on one with light copies, but the internal prints were good (better when I cleaned the LSU slit). All I had to do was clean the dust off the optics, blow out the charge unit...
  8. Replies
    2
    Views
    684

    MX-FN27N Finisher

    I installed a new

    MX-FN27 N finisher on a MX-M3050 and out of the box it would not staple the top rear single staple. All the other staple positions worked. I took it back out of the machine...
  9. Re: MX 4070N stripping black developer

    No it was just blocking the doctor blade and then blocking the toner transport pipe which caused the low level of developer and toner in the developer unit. The toner had square type chunks in it,...
  10. Re: MX 4070N stripping black developer

    43715Update: it happened the first of the week again. We called the sharp Hotline and their only suggestion was that the toner was clumping and to replace the toner and developer and to clean the...
  11. MX 4070N stripping black developer

    We have an MX 4070N stripping black developer. This is the third time in 6 weeks that we have replaced the black developer.
    I have checked that the toner is dumping into the developer unit (we are...
  12. Re: Sharp MX-B455W TROUBLE: E7-11

    We had this error on a Mx-4141 and were getting ready to replace the scan and/or ccd board and it ended up just having to reaseat connection to the CCD board
  13. Re: MX-5141N Depleted Cyan Developer After Replacement

    We have always used original Sharp Toners and Developers and still had this issue on 2 machines.
  14. Re: c554e not banner printing - have I missed something?

    Not sure about Konica Minolta but I know on Sharp Machines there is a setting for banner printing that has to be turned on in the simulations
  15. Replies
    2
    Views
    300

    [Misc] Re: MX-M565N ops panel

    I know the home screen can be changed but once you open the copy mode or other screen as far as I know the
    list of various functions cannot be changed.
  16. Replies
    9
    Views
    786

    Re: MX-6070N Copy Quality

    I would replace the main charge kit and drum first.
  17. Re: MX-5141N Depleted Cyan Developer After Replacement

    if you are an end user there are steps you need to go thru when you change the developer that a tech needs to do.
  18. Re: MX-5141N Depleted Cyan Developer After Replacement

    Just replace the unit or rebuild with the charge kit and drum. the developer only comes in the three pak :(.
  19. Re: MX-5141N Depleted Cyan Developer After Replacement

    Unfortunately this is a known issue, Start by replacing the drum and charge and see if that helps, we had two 4141 machines doing this and this fixed one of them and the other we ended up replacing...
  20. Replies
    2
    Views
    335

    Re: Sharp MX 2615 N

    PrecisionRoller.com $449.95
    Sharp MX-2615N Fuser Unit - 110 / 120 Volt
    - Genuine Sharp Fuser Assembly
  21. Replies
    23
    Views
    1,715

    Re: MX-4070 slow first copy

    Have you checked the energy save settings? Maybe change it to a fast wakeup. It looks like you have all the bases covered, I will be interested to see the solution.
  22. Replies
    2
    Views
    424

    [Misc] Re: error when selecting LCC

    I only see the LC18 or LC19 available for this model.
    Sorry that was incorrect
  23. Replies
    89
    Views
    18,466

    Re: CALLING ALL McGYVER'S

    42922Here is a picture of a customer McGyver. She attached rubber bands to a Lexmark pickup roller assembly to get by until we got there to replace the part. She really had to work at getting the...
  24. Replies
    89
    Views
    18,466

    Re: CALLING ALL McGYVER'S

    Here is a picture of a customer McGyver. She attached rubber bands to a Lexmark pickup roller assembly to get by until we got there to replace the part. She really had to work at getting the rubber...
  25. Re: What did you do before you were the copy guy or girl?

    I worked in the Grocery Business since High School and then into the Deli Bakery business of the grocery stores and then oversaw 7 bakery delis in a group of stores for over thirty years. Did a lot...
Results 1 to 25 of 237
Page 1 of 10 1 2 3 4