Search:

Type: Posts; User: plnewton

Page 1 of 2 1 2

Search: Search took 0.07 seconds.

  1. Replies
    3
    Views
    466

    Re: Fiery Reinstall

    Thanks for your reply

    Yes, I have been using remote desktop to connect to it but it is freezing during bootup so hard to tell what is going on

    I am pretty sure these are IC-413 controllers, it...
  2. Replies
    3
    Views
    466

    Fiery Reinstall

    Hi All,

    I have a C6000 running a System 9 Fiery and the drive started to produce paging errors in the event log and was lagging and taking forever to process a job, I have pulled the drive and...
  3. Replies
    7
    Views
    655

    Re: Konica c6000 installing bypass tray

    Yes that did it, thanks heaps for that..

    I must have gone though the DIPSW list 4 or 5 times but as it referred to it as the MB-504 instead of bypass I missed it

    thanks again
  4. Replies
    7
    Views
    655

    Re: Konica c6000 installing bypass tray

    cant login there any more, been retired for almost 10 years
  5. Replies
    7
    Views
    655

    Re: Konica c6000 installing bypass tray

    thanks for your reply

    where can I find the instillation manual for the bypass tray?
  6. Replies
    7
    Views
    655

    Konica c6000 installing bypass tray

    Hi All,

    we have a c6000 machine without a bypass tray and also an older (Spares machine) c6500 with a bypass tray, I have removed the everything from the c6500 and installed on the c6000 but the...
  7. Re: Printing from within service mode or test print mode

    That did the trick, thanks for that
    I was concentrating so hard on trying to send a print job in test mode that I didnt even think of looking for that option, cheers
  8. Re: Printing from within service mode or test print mode

    yes, good thinking that would get me by I think, I will see if I can find it
  9. Printing from within service mode or test print mode

    Hi All

    I have a c6000 machine that is throwing up C-4501 through to C-4503 on startup and auto color reg, the machine is producing more than adequate prints in test print mode for the current job...
  10. Replies
    8
    Views
    5,283

    Re: C-2451 Error on C6000 and a C6500

    This issue is back again, both machines have been fine for the last couple of weeks and today same deal

    Both of them just keep dumping yellow toner, if it errors out and I open it up the drum and...
  11. Replies
    8
    Views
    5,283

    Re: C-2451 Error on C6000 and a C6500

    I havent checked the exact counts yet but one would only be half way between cycles and the other would be 2/3 the way through a 200k pm cycle

    Both running OEM toners and drums

    is it possible...
  12. Replies
    8
    Views
    5,283

    C-2451 Error on C6000 and a C6500

    Hi All

    This morning to my total dismay both of our machines (a c6000 and a c6500) are coming up with a c2451 error

    I have had this from time to time on the c6500 but only ever once on the c6000...
  13. Replies
    3
    Views
    673

    C6500 Tray5 Dehumidifying Please Wait

    Hi Guys I have a C6500 machine that will not print SRA3 sheets from either tray4 or Tray5, as soon as I send a print request it shows up Tray4 (or 5) Dehumidifying Please Wait and no matter how long...
  14. Replies
    5
    Views
    843

    Re: C6500 Jamming at ADU

    Actually we got to the bottom of it this morning, as it turns out it was simply the connector for the vertical paper sensor on the PRCB, it was slightly out on one end which was not allowing the...
  15. Replies
    5
    Views
    843

    Re: C6500 Jamming at ADU

    Thanks for your reply

    All the clutches on the ADU are functioning fine, all the motors on the ADU are fine and also the paper feed motor that drives the entrance rollers on the ADU is also working...
  16. Replies
    5
    Views
    843

    C6500 Jamming at ADU

    Hi All


    Wondering if I can get a little help

    I have a C6500 Machine that jams at the entrance of the ADU, it seems to run thin A4S sheets ok through tray 1 but anything bigger or heavier it...
  17. Bearing Part number for C6500 Middle exit roller

    Hi all,

    Just wondering if someone can help me out with a part number for the two small bearing either side of the middle exit roller
    the part number for the exit roller is A03U860500 if that...
  18. Re: C6500 torn transfer belt after new drums installed

    Yes, the machine has the sep claws off it also and the stock that was being used is the same as it has for the passed twelve months

    it is hard to tell where the tear started from as it is pretty...
  19. C6500 torn transfer belt after new drums installed

    Hi all,

    We recently installed a full set of DU-104 drums in a c6500 machine as we were experiencing spotting on the black and yellow DU-102 drums and discussed here the 104 option eliminates the...
  20. Re: Missing Lines is Black on KM C6500 Sample Attatched

    We purchased the machine used and once we had it installed we discovered that it pretty much had zero maintenance done on it, the only thing we did not change was the black developing unit as it was...
  21. Re: Missing Lines is Black on KM C6500 Sample Attatched

    Hi,

    Thanks for your quick reply..

    Yes, I cleaned the slit glass yesterday when we first found it the problem

    the Mag. Roller was fine also but once I got stuck into checking it again I found...
  22. Missing Lines is Black on KM C6500 Sample Attatched

    Hi All,

    Today we have come up all of a sudden with some missing lines in the Black, the attached sample is a print in Greyscale mode and as you can see from the left we you can see 2 large missing...
  23. Replies
    2
    Views
    463

    [Misc] Re: C6500 output options

    Hi

    Yes it has, the option for the outputing on the folder is there but as soon as you try to print somthing it produces an error saying that option is not available
  24. Replies
    2
    Views
    463

    [Misc] C6500 output options

    Hi all, this might sound like a bit of a dumb question but is it possible to set different output locations on the c6500?

    we do not have the optional stacker on our machine so everything comes out...
  25. Replies
    3
    Views
    721

    Re: C6500 Dirty Backgrounds

    Any one have any idea's at all??
Results 1 to 25 of 41
Page 1 of 2 1 2