Search:

Type: Posts; User: Synaux

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. [Misc] Re: BizHub C659- issues with a certain custom document size

    I assume you are an End User? Try saving as a PDF (or save as your favorite bitmap, etc) then print from anything other than Illustrator.

    This honestly feels like you are missing something in the...
  2. Replies
    4
    Views
    274

    Re: Bizhub c550 error c4501

    Do you have the Service Manual? If you need it, make a small (or large) contribution and I will send it to you, or someone else will.
    I do not have a PRCB nearby to look at, but I found it in the...
  3. Thread: Bizhub 920

    by Synaux
    Replies
    6
    Views
    604

    Re: Bizhub 920

    I am not !@#$ing on CTN admin (there is just one, right?).
    However, I really feel there should be at least one admin responsible for each section of the forum for this reason. (I have a nomination...
  4. Re: Biz Hub C224e with DF701- scan glass assy jam?

    I recently had one bend the back corner but only about 1/4" - 1/2" with a fairly low jams. After going through it several times and finding nothing that I thought could possibly be putting the...
  5. Replies
    8
    Views
    455

    Re: Platt Tool Case Pallets - Opinions?

    Hey blackcat, your inbox is full
  6. Replies
    10
    Views
    574

    Re: Bizhub Fuser Rebuilds

    I might have missed a cross-ref, but while you are completely correct, this does not appear to be the case with the bigger/faster 4/8 series machines. :)
  7. [CQ] Re: BH C284e Counter list/ list output shrunk, squashed, condensed

    I didn't even consider the flux capacitor in those things! ;)
  8. [CQ] Re: BH C284e Counter list/ list output shrunk, squashed, condensed

    Be sure to change the laser unit before you try anything else!

    In all seriousness, I am curious to find out what figure out :)
  9. Re: Discontinued Part FS-608 + Neutralizing Brushes

    No problem. I kind of figured that might be the case.

    Thanks
  10. Replies
    10
    Views
    574

    Re: Bizhub Fuser Rebuilds

    You mean in general? I know the part numbers are different. This leads me to the perhaps absurd: Is it possible to convert a 4 series fuser to work in an 8 series and/or vice-versa?

    For the OP, I...
  11. Re: Discontinued Part FS-608 + Neutralizing Brushes

    Hey buddy, you ever get a chance to check? :)
  12. [Misc] Re: what chemicals are you using to clean one ways on KM units

    Not a huge fan of IPAs (give me gas).


    I have ~10x 5 gallon containers of blanket wash in storage (I think it is varn - pm me if you want some - I cannot give this stuff away in these parts)....
  13. Replies
    8
    Views
    455

    Re: Platt Tool Case Pallets - Opinions?

    Really? The molded pallets might be better when newerish, but these old ones are crumbling. When I close the top, simple gravity is litterally making the top pallet fitments fall off even with no...
  14. [CQ] Re: BH C284e Counter list/ list output shrunk, squashed, condensed

    This is your one and only post and you.... lol just lol
  15. Re: Help. Konica Minolta Bizhub C759 double/ghost prints on 11x17 only.

    I have seen this happen on older series with thick paper only.
  16. Replies
    8
    Views
    455

    Platt Tool Case Pallets - Opinions?

    I have a Platt 800T case with C and B pallets. The molded pallet pouches/pockets are made out of polyethylene (I think) and are literally falling apart. Quite possibly the worst material for...
  17. Discontinued Part FS-608 + Neutralizing Brushes

    Part Number: 20AK 4210 0
    PAPER CONVEYING ROLLER /A

    Goes to the Stacker unit. There is only one roller per finisher. If someone has a few I will be happy to purchase them or if someone can give...
  18. Replies
    17
    Views
    2,673

    Re: Has anybody ever seen this before?

    Wow, I do not know the data-flow, but this has to be an I/O issue:
    Network, demo and config only glitching is odd--are you [or should ask can you--no idea] on this model print the demo/config...
  19. Replies
    51
    Views
    4,699

    Re: Bizhub c224E not putting anything to paper

    Sounds like a fun trip! :P
  20. Replies
    51
    Views
    4,699

    Re: Bizhub c224E not putting anything to paper

    Fuck it. Stir the mud. I was simply trying to explain some of the contention.

    I started here knowing nearly nothing. An old timer turned me on to this forum and strongly encouraged I use his...
  21. [Misc] Re: Overall density is low, white spots on solid pattern - Pro 951

    This is out of my wheelhouse, but HV board?
  22. [Misc] Re: Overall density is low, white spots on solid pattern - Pro 951

    Paper causing this? What are you using 1800's parchment? (Or perhaps laid OR maybe even felt) with a built-in option for the feed-roller/blade/IU/dev issue?
  23. Replies
    51
    Views
    4,699

    Re: Bizhub c224E not putting anything to paper

    That is probably a marketing issue in SM and/or in admin settings... or just user settings (depends on what exactly is going on). I think you got a little lucky here. A lot of us here depend on our...
  24. Replies
    51
    Views
    4,699

    Re: Bizhub c224E not putting anything to paper

    If this guy is willing to learn how to work on his machine lets give him the benefit of the doubt

    To Ilsu, if you want to do this stuff on your own you will need a Service Manual and be willing...
  25. Re: Canon iPF780 - M40 Scanner no interpolation option & calibration

    That is what I was thinking too, hence my rant.


    Thanks, I had it "calibrate" several different ways (even intentionally slightly crooked) so I wasn't sure what it was actually trying to ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4